TP-Link EAP683-LR

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

The TP-Link EAP683-LR is MediaTek-based, IEEE 802.11ax PoE+ (802.3at) ceiling mount WiFi-6 access point with a single 2.5Gbps uplink.

PS: EAP683-UR model is hardware identical to EAP683-LR model. Hence it has been added as ALT0 variant.

Please add the installation procedure here. For now, check out Supported Since Commit field in the above table for basic flash instructions.

Additional: Installing OpenThread-BR from cc2652_backdoor

The device has a CC2652 BLE/Thread/Zigbee chip on ttyS1.
It has been tested with a firmware (ot-rcp) built from https://github.com/TexasInstruments/ot-ti and flashed using https://github.com/beagleboard/cc1352-flasher.
It has been tested with https://github.com/openwrt/packages/tree/master/net/openthread-br running as Thread Border Router (see this GitHub comment)

To flash,
1. cc2652_backdoor GPIO should be set low, and cc2652_reset should be toggled.
2. Once flashed, cc2652_backdoor should be restored high, and cc2652_reset toggled once again.
3. Once this is done, the CC2652 can be used with openthread-br using radio_url:
```
spinel+hdlc_uart:///dev/ttyS1?rtscts&uart-baudrate=921600
```
  .

Find out flash layout, then add the flash layout table here (copy, paste, modify the example).

Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.

The instructions below are for Broadcom devices and only serve as an example.
Remove / modify them if they do not apply to this particular device!

This section deals with

How you install OpenWrt from a device freshly opened
The steps required such as reset to factory defaults if the device has already been configured

Note: Reset router to factory defaults if it has been previously configured.

Browse to http://192.168.1.1/Upgrade.asp
Upload .bin file to router
Wait for it to reboot
Telnet to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed.

→ generic.flashing.tftp

Specific values needed for tftp

Enter values for “FILL-IN” below

Bootloader tftp server IPv4 address	FILL-IN
Bootloader MAC address (special)	FILL-IN
Firmware tftp image	Latest OpenWrt release (`NOTE:` Name must contain “tftp”)
TFTP transfer window	FILL-IN seconds
TFTP window start	approximately FILL-IN seconds after power on
TFTP client required IP address	FILL-IN

→ generic.sysupgrade

These are generic instructions. Update with your router's specifics.

Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
Upload image file for sysupgrade to LuCI
Wait for reboot

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:

sysupgrade
mtd

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

Login as root via SSH on 192.168.1.1, then enter the following commands:

cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc

mtd

If sysupgrade does not support this router, use mtd.

Login as root via SSH on 192.168.1.1, then enter the following commands:

cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
mtd write /tmp/xxx.abc linux && reboot

→ generic.debrick

→ failsafe_and_factory_reset

→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Please fill in real values for this device, then remove the EXAMPLEs

The default network configuration is:

Interface Name	Description	Default configuration
br-lan	EXAMPLE LAN & WiFi	EXAMPLE 192.168.1.1/24
vlan0 (eth0.0)	EXAMPLE LAN ports (1 to 4)	EXAMPLE None
vlan1 (eth0.1)	EXAMPLE WAN port	EXAMPLE DHCP
wl0	EXAMPLE WiFi	EXAMPLE Disabled

Please fill in real values for this device, then remove the EXAMPLEs

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.

Port	Switch port
Internet (WAN)	EXAMPLE 4
LAN 1	EXAMPLE 3
LAN 2	EXAMPLE 2
LAN 3	EXAMPLE 1
LAN 4	EXAMPLE 0

→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

Please fill in real values for this device, then remove the EXAMPLEs

The TP-Link EAP683-LR has the following buttons:

BUTTON	Event
EXAMPLE Reset	reset
EXAMPLE Secure Easy Setup	ses
EXAMPLE No buttons at all.	-

This table is automatically generated, once the correct filters for Brand and Model are set.
If you see “Nothing.” instead of a table, please edit this section and adjust the filters with the proper Brand and Model. Just try, it's easy.
If you still don't see a table here, or a table filled with '¿': Is there already a Techdata page available for TP-Link EAP683-LR? If not: Create one.
If you see a table with the desired device data, everything is OK and you can delete this text and the <WRAP> that encloses it.
If it still doesn't work: Don't panic, calm down, take a deep breath and contact a wiki admin (tmomas) for help.

---- datatemplatelist dttpllist ---- template: meta:template_datatemplatelist cols : Brand, Model, Versions, Device Type, Availability, Supported Since Commit_git, Supported since Rel, Supported current Rel, Unsupported, Bootloader, CPU, Target, CPU MHz, Flash MBs, RAM MB, Switch, Ethernet 100M ports_, Ethernet Gbit ports_, Comments network ports_, Modem, VLAN, WLAN 2.4GHz, WLAN 5.0GHz, WLAN Hardwares, WLAN Comments_, Detachable Antennas_, USB ports_, SATA ports_, Comments USB SATA ports_, Serial, JTAG, LED count, Button count, Power supply, Device Techdata_pageid, Forum topic URL_url, wikidevi URL_url, OEM Device Homepage URL_url, Firmware OEM Stock URL_url, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Comments_ filter : Brand=TP-Link filter : Model=EAP683-LR filter : Versions=

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Backside label:
Insert photo of backside label

→ Warranty

Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, ...

To remove the cover and open the device, do a/b/c

Main PCB:
Insert photo of PCB

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

Replace EXAMPLE by real values.

Serial connection parameters for TP-Link EAP683-LR @@Version@@	EXAMPLE 115200, 8N1, 3.3V

→ port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

→ bootloader

None so far.

F0: 102B 0000 FA: 1040 0000 FA: 1040 0000 [0200] F9: 0000 0000 V0: 0000 0000 [0001] 00: 0000 0000 BP: 2400 0041 [0000] G0: 1190 0000 EC: 0000 0000 [1000] T0: 0000 0221 [010F] Jump to BL NOTICE: BL2: v2.7(release):773f630c9-dirty NOTICE: BL2: Built : 14:19:45, Feb 14 2023 NOTICE: WDT: disabled NOTICE: CPU: MT7986 (1998MHz) NOTICE: EMI: Using DDR4 settings: size_limit=0 freq=2666 NOTICE: EMI: Detected DRAM size: 1024MB NOTICE: EMI: complex R/W mem test passed NOTICE: SPI_NAND parses attributes from parameter page. NOTICE: SPI_NAND Detected ID 0xc8 NOTICE: Page size 2048, Block size 131072, size 134217728 NOTICE: Initializing NMBM ... NOTICE: Signature found at block 1023 [0x07fe0000] NOTICE: First info table with writecount 0 found in block 960 NOTICE: Second info table with writecount 0 found in block 963 NOTICE: NMBM has been successfully attached in read-only mode NOTICE: age0=1, age1=1, so select boot_config0 NOTICE: primary_boot=0, so select FIP0 startup NOTICE: age0=1, age1=1, so select boot_config0 NOTICE: primary_boot=0, so select FIP0 startup NOTICE: BL2: Booting BL31 NOTICE: BL31: v2.7(release):773f630c9-dirty NOTICE: BL31: Built : 14:19:48, Feb 14 2023 U-Boot 2022.07-rc3 (Feb 14 2023 - 14:19:09 +0800) CPU: MediaTek MT7986 Model: mt7986-rfb DRAM: 1 GiB Core: 46 devices, 18 uclasses, devicetree: embed Initializing NMBM ... spi-nand: spi_nand spi_nand@1: GigaDevice SPI NAND was found. spi-nand: spi_nand spi_nand@1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64 Could not find a valid device for nmbm0 Signature found at block 1023 [0x07fe0000] First info table with writecount 0 found in block 960 Second info table with writecount 0 found in block 963 NMBM has been successfully attached MMC: mmc@11230000: 0 Loading Environment from MTD... mtd: partition "runtime_back" extends beyond the end of device "nmbm0" -- size truncated to 0x600000 OK In: serial@11002000 Out: serial@11002000 Err: serial@11002000 reset button is not pressed for 10s. blink led Hit Ctrl+b to stop autoboot: 1 0 ubi0: attaching mtd9 ubi0: scanning is finished ubi0: attached mtd9 (name "ubi", size 38 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 308, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1951148539 ubi0: available PEBs: 189, total reserved PEBs: 119, PEBs reserved for bad PEB handling: 19 checking volume(rootfs) passed checking volume(kernel) passed Reading from volume 'kernel' to 0x46000000, size 0x0 ... OK try to boot from ubi ## Loading kernel from FIT Image at 46000000 ... Using 'config@1' configuration Trying 'kernel@1' kernel subimage Description: ARM64 OpenWrt Linux-5.4.203 Type: Kernel Image Compression: lzma compressed Data Start: 0x460000e8 Data Size: 3076822 Bytes = 2.9 MiB Architecture: AArch64 OS: Linux Load Address: 0x48080000 Entry Point: 0x48080000 Hash algo: crc32 Hash value: 25b4cd88 Hash algo: sha1 Hash value: 335613fc663eed374560753c0a9aee7b6f680a7e Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt from FIT Image at 46000000 ... Using 'config@1' configuration Trying 'fdt@1' fdt subimage Description: ARM64 OpenWrt mt7986a-spim-nand-rfb device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x462ef508 Data Size: 23439 Bytes = 22.9 KiB Architecture: AArch64 Hash algo: crc32 Hash value: fecef150 Hash algo: sha1 Hash value: 804c15341e47552bb98c053ba2ba750e9d79b222 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x462ef508 Uncompressing Kernel Image Loading Device Tree to 000000007f7f0000, end 000000007f7f8b8e ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.4.203 (jenkins@sohoiapbuild) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16505-7bd583e)) #1 SMP Sun Oct 22 14:34:41 CST 2023 [ 0.000000] Machine model: MediaTek MT7986a RFB [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] On node 0 totalpages: 261136 [ 0.000000] DMA32 zone: 4096 pages used for memmap [ 0.000000] DMA32 zone: 0 pages reserved [ 0.000000] DMA32 zone: 261136 pages, LIFO batch:63 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 20 pages/cpu s44056 r8192 d29672 u81920 [ 0.000000] pcpu-alloc: s44056 r8192 d29672 u81920 alloc=20*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 257040 [ 0.000000] Kernel command line: console=ttyS0,115200n1 ubi.mtd=rootfs root=/dev/ubiblock0_0 rootfstype=squashfs rootwait loglevel=8 earlycon=uart8250,mmio32,0x11002000 [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1014824K/1044544K available (6270K kernel code, 488K rwdata, 1812K rodata, 384K init, 277K bss, 29720K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: CONFIG_RCU_FANOUT set to non-default value of 32. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 640 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: no VLPI support, no direct LPI support [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000 [ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns [ 0.000002] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns [ 0.008209] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=52000) [ 0.018525] pid_max: default: 32768 minimum: 301 [ 0.023234] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.030669] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.039383] ASID allocator initialised with 65536 entries [ 0.044861] rcu: Hierarchical SRCU implementation. [ 0.049970] smp: Bringing up secondary CPUs ... [ 0.054780] Detected VIPT I-cache on CPU1 [ 0.054798] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000 [ 0.054821] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.055080] Detected VIPT I-cache on CPU2 [ 0.055091] GICv3: CPU2: found redistributor 2 region 0:0x000000000c0c0000 [ 0.055100] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.055329] Detected VIPT I-cache on CPU3 [ 0.055337] GICv3: CPU3: found redistributor 3 region 0:0x000000000c0e0000 [ 0.055344] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.055372] smp: Brought up 1 node, 4 CPUs [ 0.111926] SMP: Total of 4 processors activated. [ 0.116648] CPU features: detected: 32-bit EL0 Support [ 0.121807] CPU features: detected: CRC32 instructions [ 0.127058] CPU: All CPU(s) started at EL2 [ 0.131177] alternatives: patching kernel code [ 0.137828] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.147645] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.154648] pinctrl core: initialized pinctrl subsystem [ 0.160497] NET: Registered protocol family 16 [ 0.165155] DMA: preallocated 256 KiB pool for atomic allocations [ 0.179593] cryptd: max_cpu_qlen set to 1000 [ 0.185119] SCSI subsystem initialized [ 0.189868] rbus 18000000.wbsys: PCI host bridge to bus 0000:00 [ 0.195830] pci_bus 0000:00: root bus resource [mem 0x18000000-0x18ffffff] [ 0.202737] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.208246] pci_bus 0000:00: scanning bus [ 0.212282] pci 0000:00:00.0: [14c3:7986] type 00 class 0x000280 [ 0.218324] pci 0000:00:00.0: reg 0x10: [mem 0x18000000-0x1800000f 64bit] [ 0.225144] pci 0000:00:00.0: reg 0x18: [mem 0x00000000-0x0000000f] [ 0.231439] pci 0000:00:00.0: reg 0x1c: [mem 0x00000000-0x0000000f] [ 0.237734] pci 0000:00:00.0: reg 0x20: [mem 0x00000000-0x0000000f] [ 0.244028] pci 0000:00:00.0: reg 0x24: [mem 0x00000000-0x0000000f] [ 0.251149] pci_bus 0000:00: fixups for bus [ 0.255351] pci_bus 0000:00: bus scan returning with max=00 [ 0.261209] clocksource: Switched to clocksource arch_sys_counter [ 0.267930] thermal_sys: Registered thermal governor 'fair_share' [ 0.267934] thermal_sys: Registered thermal governor 'bang_bang' [ 0.274063] thermal_sys: Registered thermal governor 'step_wise' [ 0.280094] thermal_sys: Registered thermal governor 'user_space' [ 0.286126] thermal_sys: Registered thermal governor 'power_allocator' [ 0.292478] NET: Registered protocol family 2 [ 0.303500] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.311553] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.320091] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.327908] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.335252] TCP: Hash tables configured (established 8192 bind 8192) [ 0.341721] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.348378] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.355555] NET: Registered protocol family 1 [ 0.359954] PCI: CLS 0 bytes, default 64 [ 0.364657] workingset: timestamp_bits=46 max_order=18 bucket_order=0 [ 0.373439] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.379309] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.398126] mtk-pcie 11280000.pcie: host bridge /pcie@11280000 ranges: [ 0.404706] mtk-pcie 11280000.pcie: Parsing ranges property... [ 0.410570] mtk-pcie 11280000.pcie: MEM 0x20000000..0x2fffffff -> 0x20000000 [ 0.417855] phy phy-pcie-phy@11c00000.0: try to get sw efuse [ 0.423541] phy phy-pcie-phy@11c00000.0: try to get sw efuse+ [ 0.429326] phy phy-pcie-phy@11c00000.0: u3 auto load valid efuse: ENABLE with value: 1 [ 0.437388] phy phy-pcie-phy@11c00000.0: u3 efuse - intr 2a, rx_imp 10, tx_imp 10 [ 0.444914] phy phy-pcie-phy@11c00000.0: pcie auto load valid efuse: ENABLE with value: 1 [ 0.453148] phy phy-pcie-phy@11c00000.0: u3 lane1 efuse - intr 2a, rx_imp 10, tx_imp 10 [ 0.669232] mtk-pcie 11280000.pcie: PCIe link down, ltssm reg val: 0x0 [ 0.675847] mtk-pcie: probe of 11280000.pcie failed with error -110 [ 0.689705] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 0.696600] printk: console [ttyS0] disabled [ 0.721014] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 12, base_baud = 2500000) is a ST16650V2 [ 0.730223] printk: console [ttyS0] enabled [ 0.730223] printk: console [ttyS0] enabled [ 0.738574] printk: bootconsole [uart8250] disabled [ 0.738574] printk: bootconsole [uart8250] disabled [ 0.768690] 11003000.serial: ttyS1 at MMIO 0x11003000 (irq = 13, base_baud = 1625000) is a ST16650V2 [ 0.798095] 11004000.serial: ttyS2 at MMIO 0x11004000 (irq = 14, base_baud = 1625000) is a ST16650V2 [ 0.807691] mtk_rng 1020f000.trng: registered RNG driver [ 0.807903] random: crng init done [ 0.813121] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.824130] loop: module loaded [ 0.828237] mt7986-pinctrl 1001f000.pinctrl: pin_config_set op failed for pin 36 [ 0.835625] mtk-spi 1100a000.spi: Error applying setting, reverse things back [ 0.843150] spi-nor spi0.0: unrecognized JEDEC id bytes: 00 c8 01 7f 7f 7f [ 0.850022] spi-nor: probe of spi0.0 failed with error -2 [ 0.855578] spi-nand spi0.1: ESMT SPI NAND was found. [ 0.860620] spi-nand spi0.1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64 [ 0.869309] mt7986-pinctrl 1001f000.pinctrl: pin SPI1_CLK already requested by 11003000.serial; cannot claim for 1100b000.spi [ 0.880591] mt7986-pinctrl 1001f000.pinctrl: pin-29 (1100b000.spi) status -22 [ 0.887715] mt7986-pinctrl 1001f000.pinctrl: could not request pin 29 (SPI1_CLK) from group spi1_2 on device pinctrl_moore [ 0.898817] mtk-spi 1100b000.spi: Error applying setting, reverse things back [ 0.905941] mtk-spi: probe of 1100b000.spi failed with error -22 [ 0.912820] [mtk_hw_init] reset_lock:0, force:0 [ 0.917379] [mtk_hw_init] execute fe cold reset [ 1.043714] mtk_soc_eth 15100000.ethernet: generated random MAC address 26:44:05:53:e1:55 [ 1.052120] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc011680000, irq 123 [ 1.061253] mtk_soc_eth 15100000.ethernet: generated random MAC address 9e:71:75:94:91:da [ 1.069575] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc011680000, irq 123 [ 1.078688] (unnamed net_device) (dummy): netif_napi_add() called with weight 256 [ 1.086398] i2c /dev entries driver [ 1.090671] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0) [ 1.098582] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com [ 1.107218] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433(alg:7fcdfc00)/0/0/0 [ 1.121027] Initializing XFRM netlink socket [ 1.125566] NET: Registered protocol family 10 [ 1.130508] Segment Routing with IPv6 [ 1.134220] NET: Registered protocol family 17 [ 1.138703] Bridge firewalling registered [ 1.142758] 8021q: 802.1Q VLAN Support v1.8 [ 1.154009] nmbm nmbm_spim_nand: Signature found at block 1023 [0x07fe0000] [ 1.161823] nmbm nmbm_spim_nand: First info table with writecount 0 found in block 960 [ 1.172288] nmbm nmbm_spim_nand: Second info table with writecount 0 found in block 963 [ 1.180278] nmbm nmbm_spim_nand: NMBM has been successfully attached [ 1.186851] 13 fixed-partitions partitions found on MTD device nmbm_spim_nand [ 1.193970] Creating 13 MTD partitions on "nmbm_spim_nand": [ 1.199528] 0x000000000000-0x000000100000 : "BL2" [ 1.204672] 0x000000100000-0x000000200000 : "boot-config" [ 1.210383] 0x000000200000-0x000000300000 : "boot-config1" [ 1.216146] 0x000000300000-0x000000400000 : "u-boot-env" [ 1.221749] 0x000000400000-0x000000600000 : "FIP0" [ 1.226821] 0x000000600000-0x000000800000 : "FIP1" [ 1.231908] 0x000000800000-0x000000900000 : "oops" [ 1.236990] 0x000000900000-0x000002f80000 : "rootfs" [ 1.242280] mtd: device 8 (rootfs) set to be root filesystem [ 1.248154] mtdsplit: no squashfs found in "rootfs" [ 1.253034] 0x000002f80000-0x000005600000 : "rootfs_1" [ 1.258546] 0x000005600000-0x000005e00000 : "factory_data" [ 1.264336] 0x000005e00000-0x000006a00000 : "runtime_data" [ 1.270122] 0x000006a00000-0x000007200000 : "backup_data" [ 1.275831] 0x000007200000-0x000007a00000 : "runtime_backup" [ 1.281479] mtd: partition "runtime_backup" extends beyond the end of device "nmbm_spim_nand" -- size truncated to 0x600000 [ 1.293078] ubi0: attaching mtd8 [ 1.415532] ubi0: scanning is finished [ 1.423932] ubi0: attached mtd8 (name "rootfs", size 38 MiB) [ 1.429583] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 1.436436] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 1.443204] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 1.450144] ubi0: good PEBs: 308, bad PEBs: 0, corrupted PEBs: 0 [ 1.456131] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 1.463332] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1951148539 [ 1.472439] ubi0: available PEBs: 189, total reserved PEBs: 119, PEBs reserved for bad PEB handling: 19 [ 1.481812] ubi0: background thread "ubi_bgt0d" started, PID 724 [ 2.322661] block ubiblock0_0: created from ubi0:0(rootfs) [ 2.328148] hctosys: unable to open rtc device (rtc0) [ 2.333771] UBIFS (ubi0:0): static UBI volume - read-only mode [ 2.339603] UBIFS error (ubi0:0 pid 1): ubifs_mount: cannot mount read-write - read-only media [ 2.350198] VFS: Mounted root (squashfs filesystem) readonly on device 253:0. [ 2.357482] Freeing unused kernel memory: 384K [ 2.389236] Run /sbin/init as init process init started: BusyBox v1.20.2 (2023-10-22 14:55:58 CST) starting pid 738, tty '': '/etc/rc.d/rcS' [ 2.591175] ubi1: attaching mtd10 [ 2.619378] ubi1: scanning is finished [ 2.627683] ubi1: attached mtd10 (name "factory_data", size 8 MiB) [ 2.633852] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 2.640708] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 2.647476] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 2.654416] ubi1: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0 [ 2.660317] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 2.667518] ubi1: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 1499378563 [ 2.676625] ubi1: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 19 [ 2.685738] ubi1: background thread "ubi_bgt1d" started, PID 762 UBI device number 1, total 64 LEBs (8126464 bytes, 7.8 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) ubi_factory_data found, mounting[ 2.706876] UBIFS (ubi1:0): Mounting in unauthenticated mode ... [ 2.713646] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 768 [ 2.736999] UBIFS (ubi1:0): recovery needed [ 2.840313] UBIFS (ubi1:0): recovery completed [ 2.844793] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "ubi_factory_data" [ 2.853037] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 2.862927] UBIFS (ubi1:0): FS size: 3936256 bytes (3 MiB, 31 LEBs), journal size 1269760 bytes (1 MiB, 10 LEBs) [ 2.873076] UBIFS (ubi1:0): reserved for root: 0 bytes (0 KiB) [ 2.878893] UBIFS (ubi1:0): media format: w4/r0 (latest is w5/r0), UUID A482D59E-0EB7-41C5-AAE4-41C5DD83D57E, small LPT model [ 2.894358] ubi2: attaching mtd12 [ 2.922431] ubi2: scanning is finished [ 2.930691] ubi2: attached mtd12 (name "backup_data", size 8 MiB) [ 2.936773] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 2.943629] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 2.950397] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 2.957337] ubi2: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0 [ 2.963238] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 2.970439] ubi2: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 2042421102 [ 2.979546] ubi2: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 19 [ 2.988659] ubi2: background thread "ubi_bgt2d" started, PID 776 UBI device number 2, total 64 LEBs (8126464 bytes, 7.8 MiB), ava[ 2.998835] UBIFS (ubi2:0): Mounting in unauthenticated mode ilable 0 LEBs (0[ 3.005909] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 782 bytes), LEB size 126976 bytes (124.0 KiB) ubi_backup_data found, mounting... [ 3.037516] UBIFS (ubi2:0): recovery needed [ 3.140631] UBIFS (ubi2:0): recovery completed [ 3.145110] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "ubi_backup_data" [ 3.153267] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 3.163158] UBIFS (ubi2:0): FS size: 3936256 bytes (3 MiB, 31 LEBs), journal size 1269760 bytes (1 MiB, 10 LEBs) [ 3.173306] UBIFS (ubi2:0): reserved for root: 0 bytes (0 KiB) [ 3.179122] UBIFS (ubi2:0): media format: w4/r0 (latest is w5/r0), UUID 4421AA92-E49C-49EF-9C0D-846203EC1CD4, small LPT model both fdata mount ok [ 3.195034] ubi3: attaching mtd11 [ 3.234879] ubi3: scanning is finished [ 3.243153] ubi3: attached mtd11 (name "runtime_data", size 12 MiB) [ 3.249407] ubi3: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 3.256263] ubi3: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 3.263030] ubi3: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 3.269971] ubi3: good PEBs: 96, bad PEBs: 0, corrupted PEBs: 0 [ 3.275871] ubi3: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 3.283072] ubi3: max/mean erase counter: 4/1, WL threshold: 4096, image sequence number: 1161119607 [ 3.292179] ubi3: available PEBs: 0, total reserved PEBs: 96, PEBs reserved for bad PEB handling: 19 [ 3.301293] ubi3: background thread "ubi_bgt3d" started, PID 790 UBI device number 3, total 96 LEBs (12189696 bytes, 11.6 MiB), a[ 3.311561] UBIFS (ubi3:0): Mounting in unauthenticated mode vailable 0 LEBs [ 3.318557] UBIFS (ubi3:0): background thread "ubifs_bgt3_0" started, PID 796 (0 bytes), LEB size 126976 bytes (124.0 KiB) ubi_runtime_data found, attach 11 success, mounting... [ 3.350140] UBIFS (ubi3:0): recovery needed [ 3.459651] UBIFS (ubi3:0): recovery completed [ 3.464130] UBIFS (ubi3:0): UBIFS: mounted UBI device 3, volume 0, name "ubi_runtime_data" [ 3.472375] UBIFS (ubi3:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 3.482265] UBIFS (ubi3:0): FS size: 7999488 bytes (7 MiB, 63 LEBs), journal size 1777664 bytes (1 MiB, 14 LEBs) [ 3.492414] UBIFS (ubi3:0): reserved for root: 0 bytes (0 KiB) [ 3.498232] UBIFS (ubi3:0): media format: w4/r0 (latest is w5/r0), UUID 8EE26918-0A11-40C0-B3ED-EB56A23D551F, small LPT model This Board use 5.4.203 [ 3.615815] mtdoops: ready 0, 1 (no erase) [ 3.619911] mtdoops: Attached to MTD device 7 [ 3.653179] xt_time: kernel timezone is -0000 [ 3.792595] ---portal module open ok [ 3.794337] [ 3.794337] Register vlan_manage hooks success. [ 3.819465] [Debug gpio_parse_conf:281] Open File /etc/EAP683_LR_1.0/gpio.conf SUCCESS!! [ 3.832343] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 14, readCount 256 [ 3.839913] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 44, readCount 256 [ 3.847465] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 6 , readCount 256 [ 3.855014] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 7 , readCount 256 [ 3.862563] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 2 , readCount 256 [ 3.870143] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 7 , readCount 256 [ 3.877704] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 44, readCount 256 [ 3.885358] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 6 , readCount 256 [ 3.892913] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 7 , readCount 256 [ 3.900467] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 2 , readCount 256 [ 3.908017] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 7 , readCount 256 [ 3.915566] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 44, readCount 256 [ 3.923116] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 7 , readCount 256 [ 3.930664] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 6 , readCount 256 [ 3.938212] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 6 , readCount 256 [ 3.945761] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 6 , readCount 256 [ 3.953310] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 2 , readCount 256 [ 3.960860] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 87, readCount 256 [ 3.968410] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 44, readCount 256 [ 3.975966] [Debug gpio_parse_conf:336] GPIO Parse OK: led_sys led(1) high(1) high(1) 422 [ 3.984557] [Debug gpio_parse_conf:336] GPIO Parse OK: btn_reset btn(2) low (0) high(1) 420 [ 3.993149] [Debug gpio_parse_conf:336] GPIO Parse OK: phy0_reset gpo(4) low (0) high(1) 421 [ 4.001740] [Debug gpio_parse_conf:336] GPIO Parse OK: ble_reset gpo(4) low (0) high(1) 418 [ 4.010334] [Debug gpio_parse_conf:336] GPIO Parse OK: ble_backdoor gpo(4) low (0) high(1) 455 [ 4.019014] [Debug gpio_parse_conf:336] GPIO Parse OK: ble_ptm gpo(4) low (0) high(1) 456 [ 4.027604] [Debug gpio_parse_conf:336] GPIO Parse OK: ble_grant gpo(4) high(1) low (0) 460 [ 4.036194] [Debug gpio_parse_conf:336] GPIO Parse OK: ble_coex_pri gpi(5) high(1) low (0) 459 [ 4.044870] [Debug gpio_parse_conf:336] GPIO Parse OK: ble_coex_req gpi(5) high(1) low (0) 458 [ 4.053547] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 1 , readCount 2 [ 4.060925] [Debug gpio_parse_conf:308] Ignore line (0), skipLen 1 , readCount 1 [ 4.068345] [Debug btn_netlink_init:179] btn: create netlink socket SUCCESS. [ 4.075388] [Debug wdt_module_init:249] Create watchdog proc dir SUCCESS. [ 4.082186] [Debug led_entry_handler:792] Create led_sys proc dir SUCCESS. [ 4.089584] [Debug btn_entry_handler:962] Init button: btn_reset 2 420 0 success. [ 4.097061] [Debug gpo_entry_handler:331] Create phy0_reset proc dir SUCCESS. [ 4.104274] [Debug gpo_entry_handler:331] Create ble_reset proc dir SUCCESS. [ 4.111488] [Debug gpo_entry_handler:331] Create ble_backdoor proc dir SUCCESS. [ 4.118788] [Debug gpo_entry_handler:331] Create ble_ptm proc dir SUCCESS. [ 4.126001] [Debug gpo_entry_handler:331] Create ble_grant proc dir SUCCESS. [ 4.133303] [Debug gpi_entry_handler:241] Create ble_coex_pri proc dir SUCCESS. [ 4.140677] [Debug gpi_entry_handler:241] Create ble_coex_req proc dir SUCCESS. [ 4.149391] rate_limit: module license 'BSD' taints kernel. [ 4.154965] Disabling lock debugging due to kernel taint [ 4.186419] conninfra@(mtk_conninfra_drv_init:644) Before platform_driver_register [ 4.194116] Get Index(0-TOP_MISC_BASE) phy_addr(0x11d10000) vir_addr=(0xffffffc010a2d000) size=(0x1000) [ 4.203489] Get Index(1-TOPRGU_BASE) phy_addr(0x1001c000) vir_addr=(0xffffffc010a45000) size=(0x1000) [ 4.212685] Get Index(2-GPIO_BASE) phy_addr(0x1001f000) vir_addr=(0xffffffc010a55000) size=(0x1000) [ 4.221707] Get Index(3-IOCFG_TR_BASE) phy_addr(0x11f00000) vir_addr=(0xffffffc010a5d000) size=(0x1000) [ 4.231076] Get Index(4-IOCFG_TL_BASE) phy_addr(0x11f10000) vir_addr=(0xffffffc010a65000) size=(0x1000) [ 4.240445] Get Index(5-INFRACFG_AO_BASE) phy_addr(0x10003000) vir_addr=(0xffffffc010a6d000) size=(0x1000) [ 4.250074] Get Index(6-CONN_INFRA_CFG_BASE) phy_addr(0x18001000) vir_addr=(0xffffffc010a75000) size=(0x1000) [ 4.260029] Get Index(7-CONN_INFRA_SYSRAM_BASE) phy_addr(0x18050000) vir_addr=(0xffffffc010a7d000) size=(0x1000) [ 4.270221] Get Index(8-CONN_INFRA_CLKGEN_ON_TOP_BASE) phy_addr(0x18009000) vir_addr=(0xffffffc010a85000) size=(0x1000) [ 4.280976] Get Index(9-CONN_HOST_CSR_TOP_BASE) phy_addr(0x18060000) vir_addr=(0xffffffc010a8d000) size=(0x1000) [ 4.291125] Get Index(10-CONN_INFRA_BUS_CR_BASE) phy_addr(0x1800e000) vir_addr=(0xffffffc010a95000) size=(0x1000) [ 4.301365] Get Index(11-CONN_INFRA_RGU_BASE) phy_addr(0x18000000) vir_addr=(0xffffffc010aa2000) size=(0x1000) [ 4.311340] Get Index(12-CONN_WT_SLP_CTL_REG_BASE) phy_addr(0x18005000) vir_addr=(0xffffffc010aa4000) size=(0x1000) [ 4.321749] Get Index(13-INST2_CONN_WT_SLP_CTL_REG_BASE) phy_addr(0x18085000) vir_addr=(0xffffffc010aad000) size=(0x1000) [ 4.332678] Get Index(14-CONN_RF_SPI_MST_REG_BASE) phy_addr(0x18004000) vir_addr=(0xffffffc010ab5000) size=(0x1000) [ 4.343086] Get Index(15-INST2_CONN_RF_SPI_MST_REG_BASE) phy_addr(0x18084000) vir_addr=(0xffffffc010ab7000) size=(0x1000) [ 4.354016] Get Index(16-CONN_SEMAPHORE_BASE) phy_addr(0x18070000) vir_addr=(0xffffffc010b30000) size=(0x10000) [ 4.364120] Get Index(17-CONN_AFE_CTL_BASE) phy_addr(0x18003000) vir_addr=(0xffffffc010ab9000) size=(0x1000) [ 4.373962] Get Index(18-CONN_AFE_CTL_2ND_BASE) phy_addr(0x18083000) vir_addr=(0xffffffc010abb000) size=(0x1000) [ 4.384113] Get Index(19-WF_TOP_SLPPROT_ON_BASE) phy_addr(0x184c0000) vir_addr=(0xffffffc010b50000) size=(0x10000) [ 4.394435] Get Index(20-WF_TOP_CFG_BASE) phy_addr(0x184b0000) vir_addr=(0xffffffc010abd000) size=(0x1000) [ 4.404063] Get Index(21-WF_MCU_CONFIG_LS_BASE) phy_addr(0x184f0000) vir_addr=(0xffffffc010ac5000) size=(0x1000) [ 4.414213] Get Index(22-WF_MCU_BUS_CR_BASE) phy_addr(0x18400000) vir_addr=(0xffffffc010b15000) size=(0x1000) [ 4.424104] Get Index(23-WF_MCUSYS_INFRA_BUS_FULL_U_DEBUG_CTRL_AO_BASE) phy_addr(0x18500000) vir_addr=(0xffffffc010b17000) size=(0x1000) [ 4.436333] Get Index(24-WF_TOP_CFG_ON_BASE) phy_addr(0x184c0000) vir_addr=(0xffffffc010b70000) size=(0x10000) [ 4.446320] conninfra@(FlashRead:106) Can't get mtd device! [ 4.451875] eeFlashId(0x0) isn't match with 0x7986! [ 4.451876] Flash content is empty, so use AX6000 configuration by default! [ 4.457690] conninfra@(consys_plt_hw_init:230) adie_cfg_type = 2, one_adie_dbdc = 0 [ 4.473263] [emi_mng_init] gConEmiPhyBase = [0x4fc00000] size = [0x100000] fw size = [0x100000] ops=[00000000efbc8c7b] [ 4.484064] conninfra@(mtk_conninfra_drv_init:650) After platform_driver_register [ 4.491825] ConnInfra Dev: init (0) [ 4.496788] conninfra@(_consys_polling_chipid_int:459) Read CONNSYS HW IP version successfully! (0x02070000) [ 4.506601] conninfra@(consys_bus_clock_ctrl:485) drv=[4] conninfra_bus_clock_wpll=[0]->[16] enable [ 4.515626] conninfra@(connsys_d_die_cfg:530) D-die efuse: 0x00000000 [ 4.523080] conninfra@(_connsys_a_die_chip_id_confirm:1911) adie_idx[0]: A-die CHIP ID = 0x7976, HW Version = 0x8a20 [ 4.534584] conninfra@(_connsys_a_die_chip_id_confirm:1911) adie_idx[1]: A-die CHIP ID = 0x7976, HW Version = 0x8a20 [ 4.547094] conninfra@(consys_spi_write_nolock:670) addr = 0x0a00, val = 0xffffffff [ 4.555733] conninfra@(consys_spi_write_nolock:670) addr = 0x0144, val = 0x00000002 [ 4.565379] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x00000000 [ 4.575025] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x43a60000 [ 4.588699] conninfra@(connsys_a_die_efuse_read_nolock:906) efuse = [0x00000001, 0x00c40000, 0x008700b7, 0x00000000] [ 4.600199] conninfra@(consys_spi_write_nolock:670) addr = 0x0144, val = 0x00000002 [ 4.609846] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x23a6003a [ 4.619491] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x63a7003a [ 4.633165] conninfra@(connsys_a_die_efuse_read_nolock:906) efuse = [0x00000001, 0x00c40000, 0x008700b7, 0x00000000] [ 4.644664] conninfra@(consys_spi_write_nolock:670) addr = 0x0144, val = 0x00000002 [ 4.654310] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x23a7003a [ 4.663955] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x63ac003a [ 4.677630] conninfra@(connsys_a_die_efuse_read_nolock:906) efuse = [0x00000001, 0x00c40000, 0x008700b7, 0x00000000] [ 4.689129] conninfra@(consys_spi_write_nolock:670) addr = 0x0038, val = 0x4a563b00 [ 4.697769] conninfra@(consys_spi_write_nolock:670) addr = 0x065c, val = 0x1959f80f [ 4.706408] conninfra@(consys_spi_write_nolock:670) addr = 0x0664, val = 0x34d00fe0 [ 4.716056] conninfra@(consys_spi_write_nolock:670) addr = 0x0a00, val = 0xffffffff [ 4.724695] conninfra@(consys_spi_write_nolock:670) addr = 0x0144, val = 0x00000002 [ 4.734341] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x00000000 [ 4.743987] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x43a60000 [ 4.757663] conninfra@(connsys_a_die_efuse_read_nolock:906) efuse = [0x00000001, 0x00c40000, 0x008700b3, 0x00000000] [ 4.769162] conninfra@(consys_spi_write_nolock:670) addr = 0x0144, val = 0x00000002 [ 4.778808] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x23a6003a [ 4.788454] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x63a7003a [ 4.802126] conninfra@(connsys_a_die_efuse_read_nolock:906) efuse = [0x00000001, 0x00c40000, 0x008700b3, 0x00000000] [ 4.813625] conninfra@(consys_spi_write_nolock:670) addr = 0x0144, val = 0x00000002 [ 4.823271] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x23a7003a [ 4.832917] conninfra@(consys_spi_write_nolock:670) addr = 0x0148, val = 0x63ac003a [ 4.846590] conninfra@(connsys_a_die_efuse_read_nolock:906) efuse = [0x00000001, 0x00c40000, 0x008700b3, 0x00000000] [ 4.858088] conninfra@(consys_spi_write_nolock:670) addr = 0x0038, val = 0x4a563b00 [ 4.866727] conninfra@(consys_spi_write_nolock:670) addr = 0x065c, val = 0x1959f80f [ 4.875366] conninfra@(consys_spi_write_nolock:670) addr = 0x0664, val = 0x34d00fe0 [ 4.884007] conninfra@(consys_spi_write_nolock:670) addr = 0x0070, val = 0x88888005 [ 4.893603] conninfra@(consys_spi_write_nolock:670) addr = 0x0070, val = 0x00000005 [ 4.902247] conninfra@(consys_spi_write_nolock:670) addr = 0x0070, val = 0x88888005 [ 4.911845] conninfra@(consys_spi_write_nolock:670) addr = 0x0070, val = 0x00000005 [ 4.920423] conninfra@(_consys_polling_chipid_int:459) Read CONNSYS HW IP version successfully! (0x02070000) [ 4.930225] conninfra@(_consys_hw_conninfra_wakeup:470) conninfra_wakeup refcnt=[0]->[1] wakeup!! [ 4.939081] conninfra@(_consys_hw_conninfra_sleep:490) conninfra_sleep refcnt=[1]->[0] sleep!! [ 4.947668] conninfra@(opfunc_power_on_internal:241) [Conninfra Pwr On] BT=[0] FM=[0] GPS=[0] WF=[0] CONNINFRA=[1] [ 4.971066] mediatek_soc_hnat 15100000.hnat: wan = eth1 [ 4.976308] mediatek_soc_hnat 15100000.hnat: lan = lan [ 4.981432] mediatek_soc_hnat 15100000.hnat: ppd = eth0 [ 4.986641] mediatek_soc_hnat 15100000.hnat: gmac num = 2 [ 4.992023] mediatek_soc_hnat 15100000.hnat: ppe num = 1 [ 4.997702] mediatek_soc_hnat 15100000.hnat: PPE0 entry number = 8192 [ 5.014439] mediatek_soc_hnat 15100000.hnat: PPE0 hwnat start [ 5.020234] hnat roaming work enable wlanmonitor is not supported. sh: write error: [ 5.128096] [Debug btn_netlink_receive:72] BTN netlink with user space daemon 927 SUCCESS. Invalid argument ap_watchdog is not supported. smartantenna is not supported rfscan is not supported Japan disaster mode is not enabled for region not match starting pid 950, tty '': '/sbin/getty ttyS0 115200' [Debug checkGpoParamValid:346] Param: mode off , delayon 0 , delayoff 0 , blinkCount 0. [Debug checkGpoParamValid:346] Param: mode repeat, delayon 200, delayoff 200, blinkCount 0. [Debug checkGpoParamValid:346] Param: mode off , delayon 0 , delayoff 0 , blinkCount 0. [Debug checkGpoParamValid:346] Param: mode repeat, delayon 500, delayoff 500, blinkCount 0. [Debug checkGpoParamValid:346] Param: mode off , delayon 0 , delayoff 0 , blinkCount 0. [Debug checkGpoParamValid:346] Param: mode repeat, delayon 200, delayoff 200, blinkCount 0. [Debug checkGpoParamValid:346] Param: mode on , delayon 0 , delayoff 0 , blinkCount 0. [Debug checkGpoParamValid:346] Param: mode blink, delayon 500, delayoff 500, blinkCount 4. [Debug checkGpoParamValid:346] Param: mode disable, delayon 0 , delayoff 0 , blinkCount 0. [Debug checkGpoParamValid:346] Param: mode enable, delayon 0 , delayoff 0 , blinkCount 0. [Debug checkGpoParamValid:346] Param: mode blink, delayon 200, delayoff 200, blinkCount 3000. [Debug checkGpoParamValid:346] Param: mode stop , delayon 0 , delayoff 0 , blinkCount 0. [Debug checkGpoParamValid:346] Param: mode repeat, delayon 420[ 5.256744] [Debug led_proc_write:657] Write led_sys. 0, delayoff 800,[ 5.262153] [Debug led_common_write_proc:496] Execute LED action: blinkCount 0. [ 5.262157] { 2 0 0 0 0 } [Debug checkGpoParamValid:346] Param: mode stop , delayon 0 , delayoff 0 , blinkCount 0. LED_RESET { led_sys off 1 0 0 0 } { led_sys repeat 1 200 200 0 } LED_UPDATE_START { led_sys off 1 0 0 0 } { led_sys repeat 1 500 500 0 } LED_UPDATE_FINISH { led_sys off 1 0 0 0 } LED_DUT_NO_CALDATA { led_sys repeat 4 200 200 0 } LED_SYS_INIT_PROCESS { led_sys on 0 0 0 0 } LED_SYS_INIT_OK { led_sys blink 0 500 500 4 } LED_DISABLE_ALL { led_sys disable 2 0 0 0 } LED_ENABLE_ALL { led_sys enable 0 0 0 0 } LED_LOCATE { led_sys blink 19 200 200 3000 } LED_LOCATE_STOP { led_sys stop 1 0 0 0 } LED_ISOLATED_START { led_sys repeat 2 4200 800 0 } LED_ISOLATED_FINISH { led_sys stop 0 0 0 0 } Into util_dbg_setMod, pModName(all), enable(1) [Debug gpoListenEventHandler:149] Accept a new client. [Debug gpoClientEventHandler:111] GPIOD received rule: LED_SYS_INIT_PROCESS. <debug>_radio_region_init(): 244 @ read next region flag, parse finish <debu[ 5.374545] [Debug led_proc_write:657] Write led_sys. g>_radio_region_[ 5.380728] [Debug led_common_write_proc:496] Execute LED action: init(): 273 @ r[ 5.380732] { 5 0 0 0 0 } egion:276, parse[ 5.388227] [NOTICE led_common_write_proc:533] pledconf->backup.mode 0 1 channel num:13 <debug>_radio_region_init(): 244 @ read next region flag, parse finish <debug>_radio_region_init(): 273 @ region:276, parse channel num:19 UTF8 essid(tplinktmp) The kernel doesn't support the ebtables 'filter' table. rmmod: can't unload 'ebtable_filter': unknown symbol in module, or unknown parameter [Debug gpoListenEventHandler:149] Accept a[ 5.431634] [ 5.431634] Disable VlanManage, data.enable(0), data.vid(1) new client. [Debug gpoClientEventHandler:111] GPIOD received rule: LED_ENABLE_ALL. do nothing for ax7986 switch [ 5.470025] [ 5.470025] manage vlan set port: ssh (22), http (80), https (443) [ 5.477708] [ 5.477708] manage vlan set port: ssh (22), http (80), https (443) look up /tmp/wireless/caldata.bin succ result=1 Generating 1024 bit rsa key, this may take a while... EAP683 LR aarch64 #1 SMP Sun Oct 22 14:34:41 CST 2023 (none) EAP683 LR login: Public key portion is: ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgQCoGvdKZDNpv0BhwAnuNqq/N1U3QbYXgzfIV1kq355ZyYE3NzdNoG1uJkTRdBZDYVNixeCgd0S/qzQO/2cap2FC1IrxRYP2yYt5mMEzOEfEfezhB9RE8tTNEDY1VNtv0IHs+SOruQu296O/e5pUhNij1z31W0DsOdQ/JGX2wBfeEQ== root@EAP683 LR Fingerprint: sha1!! 15:54:0f:ca:35:1a:2f:b8:ff:94:4f:8b:2c:70:aa:9e:5e:bb:b3:be Generating 1024 bit dss key, this may take a while... Public key portion is: ssh-dss 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 root@EAP683 LR Fingerprint: sha1!! 6d:80:a3:ec:ec:ba:18:8c:03:27:cf:95:ed:a4:c8:fe:82:15:66:e9 <error>radio_region_getChanCommonFlag():1056 @ invalid chanIndex:0, current channelNum = 19 insmod: can't insert '/lib/modules/5.4.203/kernel/mtkhnat.ko': File exists [ 9.334549] Adie Type: 0x7976 [ 9.334550] SKU Type: 6000 [ 9.342262] WiFi@C12L1,get_dbg_setting_by_profile() 4668: debug level setting=INDEX0_debug_level not found!! [ 9.352087] WiFi@C12L1,get_dbg_setting_by_profile() 4691: debug option setting=INDEX0_debug_option not found!! [ 9.368568] mt7986_init()--> [ 9.371475] sku:0xf, ADIE=MT7976 [ 9.375818] <--mt7986_init() [ 9.378716] RtmpRaDevCtrlInit(): MCS_LUT not used becasue MacTb size(536) > 128! [ 9.386269] WiFi@C12L1,match_index_by_chipname() 643: not find chip name INDEX1 [ 9.393579] WiFi@C12L1,match_index_by_chipname() 643: not find chip name INDEX2 [ 9.400887] WiFi@C12L1,match_index_by_chipname() 643: not find chip name INDEX3 [ 9.408194] WiFi@C12L1,match_index_by_chipname() 643: not find chip name INDEX4 [ 9.415502] WiFi@C12L1,match_index_by_chipname() 643: not find chip name INDEX5 [ 9.422809] WiFi@C12L1,match_index_by_chipname() 643: not find chip name INDEX6 [ 9.430116] WiFi@C12L1,match_index_by_chipname() 643: not find chip name INDEX7 [ 9.437422] WiFi@C12L1,match_index_by_chipname() 643: not find chip name INDEX8 [ 9.444729] WiFi@C12L1,match_index_by_chipname() 643: not find chip name INDEX9 [ 9.452018] WiFi@C12L2,match_index_by_chipname() 648: Not find slot id, back to old rule. [ 9.460318] msta_ifname not found [ 9.463674] single_ic_sku_path not found [ 9.467599] single_mkk_sku_path not found [ 9.471611] single_eg_sku_path not found [ 9.475577] bf_ic_sku_path not found [ 9.479157] bf_mkk_sku_path not found [ 9.482821] bf_eg_sku_path not found [ 9.489430] [ 9.491001] **************************************************** [ 9.497081] tp mesh netlink init [ 9.503154] **************************************************** [ 9.524401] mtk_warp_proxy: module uses symbols from proprietary module mt_wifi, inheriting taint. [ 9.536049] WiFi@C01L2,RTMP_COM_IoctlHandle() 1587: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 9.544537] msta_ifname not found [ 9.547902] single_ic_sku_path not found [ 9.551836] single_mkk_sku_path not found [ 9.555849] single_eg_sku_path not found [ 9.559817] bf_ic_sku_path not found [ 9.563395] bf_mkk_sku_path not found [ 9.567062] bf_eg_sku_path not found [ 9.638009] warp_dev0: probe of 15010000.wed2 failed with error -1 [ 9.644311] WiFi@C01L3,mt_wifi_open() 345: whnat_en=1 [ 9.777340] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(0) bss not ready (state:0, caller:TP_ROAMING_ReadParametersFromFile+0x154/0x2c0 [mt_wifi])!! [ 9.792690] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS0 PhyMode=78 [ 9.799288] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS1 PhyMode=78 [ 9.805884] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS2 PhyMode=78 [ 9.812480] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS3 PhyMode=78 [ 9.819076] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS4 PhyMode=78 [ 9.825671] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS5 PhyMode=78 [ 9.832266] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS6 PhyMode=78 [ 9.838862] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS7 PhyMode=78 [ 9.845458] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS8 PhyMode=177 [ 9.852139] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS9 PhyMode=177 [ 9.858822] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS10 PhyMode=177 [ 9.865591] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS11 PhyMode=177 [ 9.872359] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS12 PhyMode=177 [ 9.879128] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS13 PhyMode=177 [ 9.885897] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS14 PhyMode=177 [ 9.892666] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS15 PhyMode=177 [ 9.899434] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS16 PhyMode=177 [ 9.906518] WiFi@C23L3,auto_ch_select_set_cfg() 3551: BandIdx0, AutoChannelAtBootup=0, AutoChannelAlg = 0 [ 9.916061] WiFi@C23L3,auto_ch_select_set_cfg() 3551: BandIdx1, AutoChannelAtBootup=1, AutoChannelAlg = 3 [ 9.925998] WiFi@C00L2,RTMPChannelCfg() 383: Warning:ACS Enable and the 5G Channel of config parameter must set 0: [ 9.936320] WiFi@C00L2,RTMPChannelCfg() 383: Warning:ACS Enable and the 5G Channel of config parameter must set 0: [ 9.946642] WiFi@C00L2,RTMPChannelCfg() 383: Warning:ACS Enable and the 5G Channel of config parameter must set 0: [ 9.956963] WiFi@C00L2,RTMPChannelCfg() 383: Warning:ACS Enable and the 5G Channel of config parameter must set 0: [ 9.967285] WiFi@C00L2,RTMPChannelCfg() 383: Warning:ACS Enable and the 5G Channel of config parameter must set 0: [ 9.977606] WiFi@C00L2,RTMPChannelCfg() 383: Warning:ACS Enable and the 5G Channel of config parameter must set 0: [ 9.987928] WiFi@C00L2,RTMPChannelCfg() 383: Warning:ACS Enable and the 5G Channel of config parameter must set 0: [ 9.998253] WiFi@C00L2,RTMPChannelCfg() 383: Warning:ACS Enable and the 5G Channel of config parameter must set 0: [ 10.008575] WiFi@C00L2,RTMPChannelCfg() 383: Warning:ACS Enable and the 5G Channel of config parameter must set 0: [ 10.082205] IF(ra0) ==> radius_mac_type(seq-0)=0 [ 10.086807] IF(ra1) ==> radius_mac_type(seq-0)=0 [ 10.091408] IF(ra2) ==> radius_mac_type(seq-0)=0 [ 10.096009] IF(ra3) ==> radius_mac_type(seq-0)=0 [ 10.100609] IF(ra4) ==> radius_mac_type(seq-0)=0 [ 10.105209] IF(ra5) ==> radius_mac_type(seq-0)=0 [ 10.109810] IF(ra6) ==> radius_mac_type(seq-0)=0 [ 10.114411] IF(ra7) ==> radius_mac_type(seq-0)=0 [ 10.119011] IF(ra8) ==> radius_mac_type(seq-0)=0 [ 10.123612] IF(ra9) ==> radius_mac_type(seq-0)=0 [ 10.128212] IF(ra10) ==> radius_mac_type(seq-0)=0 [ 10.132899] IF(ra11) ==> radius_mac_type(seq-0)=0 [ 10.137586] IF(ra12) ==> radius_mac_type(seq-0)=0 [ 10.142273] IF(ra13) ==> radius_mac_type(seq-0)=0 [ 10.146961] IF(ra14) ==> radius_mac_type(seq-0)=0 [ 10.151648] IF(ra15) ==> radius_mac_type(seq-0)=0 [ 10.156336] IF(ra16) ==> radius_mac_type(seq-0)=0 [ 10.183155] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=0, Desired MFPC=1 [ 10.190531] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=1, Desired MFPC=1 [ 10.197906] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=2, Desired MFPC=1 [ 10.205288] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=3, Desired MFPC=1 [ 10.212663] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=4, Desired MFPC=1 [ 10.220038] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=5, Desired MFPC=1 [ 10.227414] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=6, Desired MFPC=1 [ 10.234789] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=7, Desired MFPC=1 [ 10.242164] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=8, Desired MFPC=1 [ 10.249539] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=9, Desired MFPC=1 [ 10.256920] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=10, Desired MFPC=1 [ 10.264393] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=11, Desired MFPC=1 [ 10.271859] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=12, Desired MFPC=1 [ 10.279323] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=13, Desired MFPC=1 [ 10.286786] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=14, Desired MFPC=1 [ 10.294248] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=15, Desired MFPC=1 [ 10.301722] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=16, Desired MFPC=1 [ 10.311212] WiFi@C12L1,RTMPSetProfileParameters() 9023: ra0, QoSMgmtCapa=0 [ 10.318071] WiFi@C12L1,RTMPSetProfileParameters() 9023: (null), QoSMgmtCapa=0 [ 10.325186] WiFi@C12L1,RTMPSetProfileParameters() 9023: (null), QoSMgmtCapa=0 [ 10.332302] WiFi@C12L1,RTMPSetProfileParameters() 9023: (null), QoSMgmtCapa=0 [ 10.339417] WiFi@C12L1,RTMPSetProfileParameters() 9023: (null), QoSMgmtCapa=0 [ 10.346533] WiFi@C12L1,RTMPSetProfileParameters() 9023: (null), QoSMgmtCapa=0 [ 10.353649] WiFi@C12L1,RTMPSetProfileParameters() 9023: (null), QoSMgmtCapa=0 [ 10.360765] WiFi@C12L1,RTMPSetProfileParameters() 9023: (null), QoSMgmtCapa=0 [ 10.367880] WiFi@C12L1,RTMPSetProfileParameters() 9023: (null), QoSMgmtCapa=0 [ 10.374996] WiFi@C12L1,RTMPSetProfileParameters() 9023: (null), QoSMgmtCapa=0 [ 10.382112] WiFi@C12L1,RTMPSetProfileParameters() 9023: (null), QoSMgmtCapa=0 [ 10.389228] WiFi@C12L1,RTMPSetProfileParameters() 9023: (null), QoSMgmtCapa=0 [ 10.396343] WiFi@C12L1,RTMPSetProfileParameters() 9023: (null), QoSMgmtCapa=0 [ 10.403459] WiFi@C12L1,RTMPSetProfileParameters() 9023: (null), QoSMgmtCapa=0 [ 10.410574] WiFi@C12L1,RTMPSetProfileParameters() 9023: (null), QoSMgmtCapa=0 [ 10.417690] WiFi@C12L1,RTMPSetProfileParameters() 9023: (null), QoSMgmtCapa=0 [ 10.424805] WiFi@C12L1,RTMPSetProfileParameters() 9023: (null), QoSMgmtCapa=0 [ 10.442699] WiFi@C12L1,rtmp_read_ap_client_from_file() 1649: APCLI[0] ApCliMuMimoDlEnable = 0 [ 10.451202] WiFi@C12L1,rtmp_read_ap_client_from_file() 1649: APCLI[1] ApCliMuMimoDlEnable = 0 [ 10.459896] WiFi@C12L1,rtmp_read_ap_client_from_file() 1668: APCLI[0] ApCliMuMimoUlEnable = 0 [ 10.468399] WiFi@C12L1,rtmp_read_ap_client_from_file() 1668: APCLI[1] ApCliMuMimoUlEnable = 0 [ 10.479084] WiFi@C03L1,AndesSendCmdMsg() 754: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD [ 10.490276] WiFi@C03L2,AndesSendCmdMsg() 765: Command type = ed, Extension command type = 48 [ 10.498697] WiFi@C03L1,AndesSendCmdMsg() 754: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD [ 10.509889] WiFi@C03L2,AndesSendCmdMsg() 765: Command type = ed, Extension command type = 48 [ 10.580937] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 10.587177] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(0)= Len=0 [ 10.594021] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 10.600260] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(1)= Len=0 [ 10.607103] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 10.613343] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(2)= Len=0 [ 10.620187] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 10.626426] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(3)= Len=0 [ 10.633272] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 10.639511] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(4)= Len=0 [ 10.646355] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 10.652597] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(5)= Len=0 [ 10.659442] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 10.665682] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(6)= Len=0 [ 10.672527] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 10.678767] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(7)= Len=0 [ 10.685752] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 10.692133] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(8)= Len=0 [ 10.699117] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 10.705496] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(9)= Len=0 [ 10.712482] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 10.718862] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(10)= Len=0 [ 10.725934] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 10.732315] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(11)= Len=0 [ 10.739386] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 10.745768] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(12)= Len=0 [ 10.752839] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 10.759221] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(13)= Len=0 [ 10.766300] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 10.772681] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(14)= Len=0 [ 10.779754] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 10.786140] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(15)= Len=0 [ 10.800446] I/F(ra0) FtPmkR1Local=0 [ 10.803920] I/F(ra1) FtPmkR1Local=0 [ 10.807393] I/F(ra2) FtPmkR1Local=0 [ 10.810867] I/F(ra3) FtPmkR1Local=0 [ 10.814340] I/F(ra4) FtPmkR1Local=0 [ 10.817814] I/F(ra5) FtPmkR1Local=0 [ 10.821287] I/F(ra6) FtPmkR1Local=0 [ 10.824758] I/F(ra7) FtPmkR1Local=0 [ 10.828232] I/F(ra8) FtPmkR1Local=0 [ 10.831706] I/F(ra9) FtPmkR1Local=0 [ 10.835180] I/F(ra10) FtPmkR1Local=0 [ 10.838740] I/F(ra11) FtPmkR1Local=0 [ 10.842300] I/F(ra12) FtPmkR1Local=0 [ 10.845861] I/F(ra13) FtPmkR1Local=0 [ 10.849421] I/F(ra14) FtPmkR1Local=0 [ 10.852978] I/F(ra15) FtPmkR1Local=0 [ 10.856538] I/F(ra16) FtPmkR1Local=0 [ 10.860321] I/F(ra0) pmkR0LifeTime=0 [ 10.863881] I/F(ra1) pmkR0LifeTime=0 [ 10.867441] I/F(ra2) pmkR0LifeTime=0 [ 10.871002] I/F(ra3) pmkR0LifeTime=0 [ 10.874562] I/F(ra4) pmkR0LifeTime=0 [ 10.878126] I/F(ra5) pmkR0LifeTime=0 [ 10.881688] I/F(ra6) pmkR0LifeTime=0 [ 10.885249] I/F(ra7) pmkR0LifeTime=0 [ 10.888806] I/F(ra8) pmkR0LifeTime=0 [ 10.892367] I/F(ra9) pmkR0LifeTime=0 [ 10.895927] I/F(ra10) pmkR0LifeTime=0 [ 10.899574] I/F(ra11) pmkR0LifeTime=0 [ 10.903221] I/F(ra12) pmkR0LifeTime=0 [ 10.906868] I/F(ra13) pmkR0LifeTime=0 [ 10.910514] I/F(ra14) pmkR0LifeTime=0 [ 10.914162] I/F(ra15) pmkR0LifeTime=0 [ 10.917808] I/F(ra16) pmkR0LifeTime=0 [ 10.921679] I/F(ra0) pmkR1LifeTime=0 [ 10.925239] I/F(ra1) pmkR1LifeTime=0 [ 10.928797] I/F(ra2) pmkR1LifeTime=0 [ 10.932358] I/F(ra3) pmkR1LifeTime=0 [ 10.935917] I/F(ra4) pmkR1LifeTime=0 [ 10.939479] I/F(ra5) pmkR1LifeTime=0 [ 10.943039] I/F(ra6) pmkR1LifeTime=0 [ 10.946600] I/F(ra7) pmkR1LifeTime=0 [ 10.950160] I/F(ra8) pmkR1LifeTime=0 [ 10.953720] I/F(ra9) pmkR1LifeTime=0 [ 10.957281] I/F(ra10) pmkR1LifeTime=0 [ 10.960924] I/F(ra11) pmkR1LifeTime=0 [ 10.964571] I/F(ra12) pmkR1LifeTime=0 [ 10.968217] I/F(ra13) pmkR1LifeTime=0 [ 10.971864] I/F(ra14) pmkR1LifeTime=0 [ 10.975512] I/F(ra15) pmkR1LifeTime=0 [ 10.979158] I/F(ra16) pmkR1LifeTime=0 [ 11.049389] sku:0xf, ADIE=MT7976 [ 11.053735] using E1 ROM patch [ 11.056772] using E1 RAM [ 11.059297] current sync CR = 0x1 [ 11.070375] Built date: 20230602115021a [ 11.074305] Platform: ALPS [ 11.077085] HW/SW version: 0x8a108a10 [ 11.080822] Patch version: 0xffffffff [ 11.091381] current sync CR = 0x1 [ 11.219596] Chip ID: 0x0f [ 11.222336] Eco version: 0x00 [ 11.225378] Region number: 0x0b [ 11.228590] Format version: 0x02 [ 11.231898] Format flag: 0x01 [ 11.234940] Ram version: ____000000 [ 11.238504] Built date: 20230602115044 [ 11.242329] Common crc: 0x9faa32f8 [ 11.245807] Release info: header tag = 0, total length = 80 [ 11.251449] tag 1, padding length = 1, tag length = 75 [ 11.256655] payload: t-neptune-main-2111-7986-imp-MT7986_E1_ASIC_ROM_RAM_REBB_IMP-20230602114602 [ 11.327124] Chip ID: 0x00 [ 11.329860] Eco version: 0x00 [ 11.332898] Region number: 0x03 [ 11.336113] Format version: 0x02 [ 11.339415] Format flag: 0x01 [ 11.342456] Ram version: DEV_000000 [ 11.346020] Built date: 20220906160431 [ 11.349845] Common crc: 0xa649edb8 [ 11.353324] Release info: header tag = 0, total length = 0 [ 11.453889] current sync CR = 0x7 [ 11.457265] efuse_probe: efuse = deaddead [ 11.461284] sku:0xf, ADIE=MT7976 [ 11.465625] Use default BIN from:/tmp/wireless/caldata.bin. [ 11.472040] sku:0xf, ADIE=MT7976 [ 11.478062] WiFi@C02L1,is_cal_free_ic() 1009: is_cal_free_ic(1009) offset:1000, 0,a [ 11.486483] sku:0xf, ADIE=MT7976 [ 11.504730] sku:0xf, ADIE=MT7976 [ 11.523146] WiFi@C02L1,is_cal_free_ic() 1028: iCal free [ 11.529137] sku:0xf, ADIE=MT7976 [ 15.508459] WiFi@C17L1,RTMPReadTxPwrPerRate() 450: (450): Don't Support this now! [ 15.515972] WiFi@C01L1,AntCfgInit() 3193: Not support for HIF_MT yet! [ 15.523370] WiFi@C01L1,RtmpOSFileOpen() 1012: Error 2 opening /tmp/wireless/mt7986_CE_sku_bf.dat [ 15.532135] --> Error opening file </tmp/wireless/mt7986_CE_sku_bf.dat> [ 15.538732] WiFi@C17L1,MtPwrLimitLoadParamHandle() 117: Read Power Table Error!! [ 15.553903] ch_switch_monitor_state_machine_init:: enter [ 15.559201] ch_switch_monitor_cfg_reset:: enter [ 15.563719] ch_switch_monitor_cfg_reset:: enter [ 15.568564] WiFi@C17L1,tx_pwr_comp_init() 641: NotSupportYet! [ 15.574409] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 15.579882] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 15.585353] WiFi@C14L1,IPMacTable_init() 348: IPMacTable already inited! [ 15.612250] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 15.617738] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 15.623160] WiFi@C00L1,set_ack_timeout_mode_byband() 13475: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 15.633053] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13563: DAT config band(0) cck_timeout Fail! [ 15.641728] WiFi@C00L1,set_ack_timeout_mode_byband() 13475: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 15.651617] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13574: DAT config band(0) ofdm_timeout Fail! [ 15.660379] WiFi@C00L1,set_ack_timeout_mode_byband() 13475: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 15.670268] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13585: DAT config band(0) ofdma_timeout Fail! [ 15.679116] WiFi@C00L1,set_ack_timeout_mode_byband() 13475: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 15.689004] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13563: DAT config band(1) cck_timeout Fail! [ 15.697680] WiFi@C00L1,set_ack_timeout_mode_byband() 13475: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 15.707568] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13574: DAT config band(1) ofdm_timeout Fail! [ 15.716329] WiFi@C00L1,set_ack_timeout_mode_byband() 13475: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 15.726217] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13585: DAT config band(1) ofdma_timeout Fail! [ 15.739738] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 15.747146] /home/jenkins/workspace/PROJECT_EAP683LR_V1/build/../sdk/mtk/mt7986/drivers/mt_wifi/mt_wifi_ap/../mt_wifi/hw_ctrl/cmm_chip_mt.c-MtAsicSetApcliWdevIfAddr mbss_idx = 0, if_addr = a2 e9 31 7 cc 10 [ 15.766115] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 15.773525] /home/jenkins/workspace/PROJECT_EAP683LR_V1/build/../sdk/mtk/mt7986/drivers/mt_wifi/mt_wifi_ap/../mt_wifi/hw_ctrl/cmm_chip_mt.c-MtAsicSetApcliWdevIfAddr mbss_idx = 1, if_addr = a6 e9 31 7 cc 11 [ 15.796384] :(op = 1) [ 15.803420] WiFi@C00L1,FastPathCheckMIC() 1010: (ret = 0)(op:1) [ 15.809334] WiFi@C00L2,red_tail_drop_init() 83: red_tail_drop_init: available token:8192, whnat_en:1 [ 15.818450] WiFi@C00L1,MtCmdCr4RedSet() 914: MtCmdCr4RedSet: (ret = 0) [ 15.824960] WiFi@C00L1,SendRedCmd() 1049: SendRedCmd:(ret = 1) [ 15.830843] WiFi@C01L2,RTMP_COM_IoctlHandle() 1564: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 15.838833] WiFi@C01L3,wifi_sys_open() 880: wdev idx = 0 [ 15.844409] WiFi@C18L3,BuildChannelList() 484: [ 15.848940] WiFi@C00L3,BuildChannelList() 514: BandIdx = 0, PhyMode = 78, ChListNum = 13: [ 15.857100] WiFi@C14L1,vht80_channel_group() 1571: invalid ch_band 0 [ 15.863435] WiFi@C14L1,vht160_channel_group() 1640: invalid ch_band 0 [ 15.869857] WiFi@C14L1,vht80_channel_group() 1571: invalid ch_band 0 [ 15.876192] WiFi@C14L1,vht160_channel_group() 1640: invalid ch_band 0 [ 15.882614] WiFi@C14L1,vht80_channel_group() 1571: invalid ch_band 0 [ 15.888949] WiFi@C14L1,vht160_channel_group() 1640: invalid ch_band 0 [ 15.895371] WiFi@C14L1,vht80_channel_group() 1571: invalid ch_band 0 [ 15.901705] WiFi@C14L1,vht160_channel_group() 1640: invalid ch_band 0 [ 15.908128] WiFi@C14L1,vht80_channel_group() 1571: invalid ch_band 0 [ 15.914463] WiFi@C14L1,vht160_channel_group() 1640: invalid ch_band 0 [ 15.920885] WiFi@C14L1,vht80_channel_group() 1571: invalid ch_band 0 [ 15.927219] WiFi@C14L1,vht160_channel_group() 1640: invalid ch_band 0 [ 15.933641] WiFi@C14L1,vht80_channel_group() 1571: invalid ch_band 0 [ 15.939976] WiFi@C14L1,vht160_channel_group() 1640: invalid ch_band 0 [ 15.946398] WiFi@C14L1,vht80_channel_group() 1571: invalid ch_band 0 [ 15.952733] WiFi@C14L1,vht160_channel_group() 1640: invalid ch_band 0 [ 15.959154] WiFi@C14L1,vht80_channel_group() 1571: invalid ch_band 0 [ 15.965489] WiFi@C14L1,vht160_channel_group() 1640: invalid ch_band 0 [ 15.971911] WiFi@C14L1,vht80_channel_group() 1571: invalid ch_band 0 [ 15.978246] WiFi@C14L1,vht160_channel_group() 1640: invalid ch_band 0 [ 15.984668] WiFi@C14L1,vht80_channel_group() 1571: invalid ch_band 0 [ 15.991003] WiFi@C14L1,vht160_channel_group() 1640: invalid ch_band 0 [ 15.997425] WiFi@C14L1,vht80_channel_group() 1571: invalid ch_band 0 [ 16.003759] WiFi@C14L1,vht160_channel_group() 1640: invalid ch_band 0 [ 16.010182] WiFi@C14L1,vht80_channel_group() 1571: invalid ch_band 0 [ 16.016517] WiFi@C14L1,vht160_channel_group() 1640: invalid ch_band 0 [ 16.022939] WiFi@C23L1,DfsBuildChannelList() 3703: [RDM]: wdev is not 5G. [ 16.029730] WiFi@C23L3,RadarStateCheck() 244: Zero Wait State: 0 [ 16.035721] WiFi@C23L3,operate_loader_phy() 394: oper_cfg: prim_ch(6), ht_bw(1), extcha(3), vht_bw(0), cen_ch_2(0), PhyMode=78! [ 16.047174] WiFi@C23L3,operate_loader_phy() 408: oper_dev after adjust: bw(1), prim_ch(6), cen_ch_1(4), cen_ch_2(0),ext_cha(3)! [ 16.058632] WiFi@C23L3,operate_loader_phy() 428: oper_radio after decision: bw(1), prim_ch(6), cen_ch_1(4), cen_ch_2(0)! [ 16.069500] WiFi@C00L1,mt7986_apply_dpd_flatness_data() 622: eeprom 0x19a bit 0 is 0, do runtime cal [ 16.078634] WiFi@C03L3,MtCmdChannelSwitch() 2542: ctrl_chl=6, ctrl_ch2=0, cent_ch=4 DBDCIdx=0, ChBand=0, BW=1, TXStream=4, RXStream=4, scan(0) [ 16.405353] WiFi@C03L3,MtCmdSetTxRxPath() 2803: ctrl_chl=6, ctrl_ch2=0, cent_ch=4, RxPath=f, BandIdx=0, ChBand=0, BW=1,TXStream=4, RXStream=15, scan(0) [ 16.419020] WiFi@C12L1,EDCCAInit() 21458: EDCCA compensation: uni_compensation=0, bw_compensation=0, final compensation=0 [ 16.430242] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xa4/0x158 [mt_wifi] [ 16.438239] /home/jenkins/workspace/PROJECT_EAP683LR_V1/build/../sdk/mtk/mt7986/drivers/mt_wifi/mt_wifi_ap/../mt_wifi/hw_ctrl/cmm_chip_mt.c-MtAsicSetMbssWdevIfAddrGen2 mbss_idx = 0, if_addr = 5c e9 31 7 cc 10 [ 16.456708] wdev_attr_update(): wdevId0 = 5c:e9:31:07:cc:10 [ 16.462280] WiFi@C12L1,wifi_sys_open() 931: wifi_sys_open():band0 group_idx[0]=0, bw_grp=16 omac=0 [ 16.471256] WiFi@C08L3,hw_ctrl_flow_v2_open() 13: wdev_idx=0 [ 16.477074] WiFi@C02L2,AsicRadioOnOffCtrl() 2340: DbdcIdx=0 RadioOn [ 16.483884] WiFi@C00L2,ApAutoChannelAtBootUp() 342: -----------------> [ 16.492436] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 16.497959] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 16.503343] WiFi@C00L1,ApAutoChannelAtBootUp() 506: not A band [ 16.509158] WiFi@C08L1,ap_run_at_boot() 632: ACS is disable !! [ 16.515988] WiFi@C08L2,APStartUpForMbss() 1001: ===>(caller:ap_inf_open+0x1b4/0x5d8 [mt_wifi]), mbss_idx:0, CfgMode:0 [ 16.526577] WiFi@C15L2,APPMFInit() 130: [PMF] Security is not WPA2/WPA2PSK AES [ 16.533782] WiFi@C15L2,APPMFInit() 142: [PMF] apidx=0, MFPC=0, MFPR=0, SHA256=0 [ 16.541076] WiFi@C18L3,BuildChannelList() 484: [ 16.545856] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 16.553349] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 16.558765] WiFi@C00L1,mt7986_apply_dpd_flatness_data() 622: eeprom 0x19a bit 0 is 0, do runtime cal [ 16.567886] WiFi@C03L3,MtCmdChannelSwitch() 2542: ctrl_chl=1, ctrl_ch2=0, cent_ch=1 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 16.626696] WiFi@C03L3,MtCmdSetTxRxPath() 2803: ctrl_chl=1, ctrl_ch2=0, cent_ch=1, RxPath=f, BandIdx=0, ChBand=0, BW=0,TXStream=4, RXStream=15, scan(1) [ 16.640457] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 16.957322] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 16.962720] WiFi@C00L1,mt7986_apply_dpd_flatness_data() 622: eeprom 0x19a bit 0 is 0, do runtime cal [ 16.971838] WiFi@C03L3,MtCmdChannelSwitch() 2542: ctrl_chl=2, ctrl_ch2=0, cent_ch=2 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 17.030632] WiFi@C03L3,MtCmdSetTxRxPath() 2803: ctrl_chl=2, ctrl_ch2=0, cent_ch=2, RxPath=f, BandIdx=0, ChBand=0, BW=0,TXStream=4, RXStream=15, scan(1) [ 17.044392] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 17.373336] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 17.378758] WiFi@C00L1,mt7986_apply_dpd_flatness_data() 622: eeprom 0x19a bit 0 is 0, do runtime cal [ 17.387882] WiFi@C03L3,MtCmdChannelSwitch() 2542: ctrl_chl=3, ctrl_ch2=0, cent_ch=3 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 17.446655] WiFi@C03L3,MtCmdSetTxRxPath() 2803: ctrl_chl=3, ctrl_ch2=0, cent_ch=3, RxPath=f, BandIdx=0, ChBand=0, BW=0,TXStream=4, RXStream=15, scan(1) [ 17.460417] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 17.789298] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 17.794702] WiFi@C00L1,mt7986_apply_dpd_flatness_data() 622: eeprom 0x19a bit 0 is 0, do runtime cal [ 17.803821] WiFi@C03L3,MtCmdChannelSwitch() 2542: ctrl_chl=4, ctrl_ch2=0, cent_ch=4 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 17.862597] WiFi@C03L3,MtCmdSetTxRxPath() 2803: ctrl_chl=4, ctrl_ch2=0, cent_ch=4, RxPath=f, BandIdx=0, ChBand=0, BW=0,TXStream=4, RXStream=15, scan(1) [ 17.876312] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 18.205305] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 18.210712] WiFi@C00L1,mt7986_apply_dpd_flatness_data() 622: eeprom 0x19a bit 0 is 0, do runtime cal [ 18.219832] WiFi@C03L3,MtCmdChannelSwitch() 2542: ctrl_chl=5, ctrl_ch2=0, cent_ch=5 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 18.278637] WiFi@C03L3,MtCmdSetTxRxPath() 2803: ctrl_chl=5, ctrl_ch2=0, cent_ch=5, RxPath=f, BandIdx=0, ChBand=0, BW=0,TXStream=4, RXStream=15, scan(1) [ 18.292412] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 18.621304] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 18.626713] WiFi@C00L1,mt7986_apply_dpd_flatness_data() 622: eeprom 0x19a bit 0 is 0, do runtime cal [ 18.635833] WiFi@C03L3,MtCmdChannelSwitch() 2542: ctrl_chl=6, ctrl_ch2=0, cent_ch=6 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 18.694609] WiFi@C03L3,MtCmdSetTxRxPath() 2803: ctrl_chl=6, ctrl_ch2=0, cent_ch=6, RxPath=f, BandIdx=0, ChBand=0, BW=0,TXStream=4, RXStream=15, scan(1) [ 18.708369] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 19.037312] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 19.042723] WiFi@C00L1,mt7986_apply_dpd_flatness_data() 622: eeprom 0x19a bit 0 is 0, do runtime cal [ 19.051843] WiFi@C03L3,MtCmdChannelSwitch() 2542: ctrl_chl=7, ctrl_ch2=0, cent_ch=7 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 19.110645] WiFi@C03L3,MtCmdSetTxRxPath() 2803: ctrl_chl=7, ctrl_ch2=0, cent_ch=7, RxPath=f, BandIdx=0, ChBand=0, BW=0,TXStream=4, RXStream=15, scan(1) [ 19.124405] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 19.453333] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 19.458757] WiFi@C00L1,mt7986_apply_dpd_flatness_data() 622: eeprom 0x19a bit 0 is 0, do runtime cal [ 19.467879] WiFi@C03L3,MtCmdChannelSwitch() 2542: ctrl_chl=8, ctrl_ch2=0, cent_ch=8 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 19.526672] WiFi@C03L3,MtCmdSetTxRxPath() 2803: ctrl_chl=8, ctrl_ch2=0, cent_ch=8, RxPath=f, BandIdx=0, ChBand=0, BW=0,TXStream=4, RXStream=15, scan(1) [ 19.540431] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 19.869297] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 19.874696] WiFi@C00L1,mt7986_apply_dpd_flatness_data() 622: eeprom 0x19a bit 0 is 0, do runtime cal [ 19.883813] WiFi@C03L3,MtCmdChannelSwitch() 2542: ctrl_chl=9, ctrl_ch2=0, cent_ch=9 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 19.942618] WiFi@C03L3,MtCmdSetTxRxPath() 2803: ctrl_chl=9, ctrl_ch2=0, cent_ch=9, RxPath=f, BandIdx=0, ChBand=0, BW=0,TXStream=4, RXStream=15, scan(1) [ 19.956377] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 20.285352] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 20.290780] WiFi@C00L1,mt7986_apply_dpd_flatness_data() 622: eeprom 0x19a bit 0 is 0, do runtime cal [ 20.299904] WiFi@C03L3,MtCmdChannelSwitch() 2542: ctrl_chl=10, ctrl_ch2=0, cent_ch=10 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(1) [ 20.358862] WiFi@C03L3,MtCmdSetTxRxPath() 2803: ctrl_chl=10, ctrl_ch2=0, cent_ch=10, RxPath=f, BandIdx=0, ChBand=0, BW=0,TXStream=4, RXStream=15, scan(1) [ 20.372798] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 20.701212] WiFi@C23L3,operate_loader_phy() 394: oper_cfg: prim_ch(6), ht_bw(1), extcha(3), vht_bw(0), cen_ch_2(0), PhyMode=78! [ 20.712669] WiFi@C23L3,operate_loader_phy() 408: oper_dev after adjust: bw(1), prim_ch(6), cen_ch_1(4), cen_ch_2(0),ext_cha(3)! [ 20.724131] WiFi@C23L3,operate_loader_phy() 428: oper_radio after decision: bw(1), prim_ch(6), cen_ch_1(4), cen_ch_2(0)! [ 20.734996] WiFi@C00L1,mt7986_apply_dpd_flatness_data() 622: eeprom 0x19a bit 0 is 0, do runtime cal [ 20.744112] WiFi@C03L3,MtCmdChannelSwitch() 2542: ctrl_chl=6, ctrl_ch2=0, cent_ch=4 DBDCIdx=0, ChBand=0, BW=1, TXStream=4, RXStream=4, scan(0) [ 21.066565] WiFi@C03L3,MtCmdSetTxRxPath() 2803: ctrl_chl=6, ctrl_ch2=0, cent_ch=4, RxPath=f, BandIdx=0, ChBand=0, BW=1,TXStream=4, RXStream=15, scan(0) [ 21.080216] WiFi@C12L1,EDCCAInit() 21458: EDCCA compensation: uni_compensation=0, bw_compensation=0, final compensation=0 [ 21.091171] WiFi@C23L3,operate_loader_phy() 394: oper_cfg: prim_ch(6), ht_bw(0), extcha(0), vht_bw(0), cen_ch_2(0), PhyMode=78! [ 21.102625] WiFi@C23L3,operate_loader_phy() 408: oper_dev after adjust: bw(0), prim_ch(6), cen_ch_1(6), cen_ch_2(0),ext_cha(0)! [ 21.114081] WiFi@C23L3,operate_loader_phy() 428: oper_radio after decision: bw(0), prim_ch(6), cen_ch_1(6), cen_ch_2(0)! [ 21.124936] WiFi@C00L1,mt7986_apply_dpd_flatness_data() 622: eeprom 0x19a bit 0 is 0, do runtime cal [ 21.134052] WiFi@C03L3,MtCmdChannelSwitch() 2542: ctrl_chl=6, ctrl_ch2=0, cent_ch=6 DBDCIdx=0, ChBand=0, BW=0, TXStream=4, RXStream=4, scan(0) [ 21.181475] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(0) bss not ready (state:0, caller:update_ap_qload_to_bcn+0xac/0xd0 [mt_wifi])!! [ 21.440821] WiFi@C03L3,MtCmdSetTxRxPath() 2803: ctrl_chl=6, ctrl_ch2=0, cent_ch=6, RxPath=f, BandIdx=0, ChBand=0, BW=0,TXStream=4, RXStream=15, scan(0) [ 21.454482] WiFi@C12L1,EDCCAInit() 21458: EDCCA compensation: uni_compensation=0, bw_compensation=0, final compensation=0 [ 21.465725] WiFi@C08L2,ap_link_up() 7210: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(0) [ 21.474325] WiFi@C01L3,wifi_sys_linkup() 1291: wdev idx = 0 [ 21.480110] WiFi@C00L3,wtc_acquire_groupkey_wcid() 84: Found a non-occupied wtbl_idx:535 for WDEV_TYPE:1 [ 21.480110] LinkToOmacIdx = 0, LinkToWdevType = 1 [ 21.494457] WiFi@C08L3,hw_ctrl_flow_v2_link_up() 72: wdev_idx=0 [ 21.508481] WiFi@C08L3,UpdateBeaconHandler() 1916: BCN_UPDATE_INIT, OmacIdx = 0 (ra0) [ 21.516303] WiFi@C08L3,UpdateBeaconHandler() 1929: Band0 BcnInitedRnd = 53 [ 21.523282] WiFi@C00L1,TxCCKStreamCtrl() 20922: set wrong parameters [ 21.539372] PrintSrCmd: [ 21.539372] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 21.539372] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 21.553342] PrintSrCmd: [ 21.553342] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 21.553342] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 21.567317] PrintSrCmd: [ 21.567317] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 21.567317] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 21.581284] PrintSrCmd: [ 21.581284] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 21.581284] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 21.595338] PrintSrCmd: [ 21.595338] u1CmdSubId = 31, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 21.595338] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 21.609400] PrintSrCmd: [ 21.609400] u1CmdSubId = 33, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 21.609400] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 21.623478] WiFi@C12L1,EDCCAInit() 21458: EDCCA compensation: uni_compensation=0, bw_compensation=0, final compensation=0 [ 21.634414] WiFi@C03L3,MtCmdTxPwrShowInfo() 13750: ucTxPowerInfoCatg: 2, BandIdx: 0 [ 21.642141] WiFi@C03L3,MtCmdTxPwrShowInfo() 13779: (ret = 0) [ 21.642234] [mtf_txpower_all_rate_info] band_idx:0 pwr:24 ChBand:2G ePAGain:0 [ 21.658982] WiFi@C01L2,RTMP_COM_IoctlHandle() 1575: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DOWN [ 21.667421] WiFi@C08L2,ap_link_down() 7228: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(0) [ 21.676726] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(0) bss not ready (state:2, caller:ap_link_down+0x90/0x128 [mt_wifi])!! [ 21.688099] WiFi@C01L3,wifi_sys_linkdown() 1444: wdev idx = 0 [ 21.694050] WiFi@C08L3,hw_ctrl_flow_v2_link_down() 123: wdev_idx=0 [ 21.703073] WiFi@C01L3,wifi_sys_close() 969: wdev idx = 0 [ 21.708688] WiFi@C08L3,hw_ctrl_flow_v2_close() 41: wdev_idx=0 [ 21.714571] WiFi@C01L2,RTMP_COM_IoctlHandle() 1598: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_DEINIT [ 21.723010] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(0) bss not ready (state:0, caller:APStopByBss+0xf8/0x4d0 [mt_wifi])!! [ 21.734296] WiFi@C01L2,wifi_sys_disconn_act() 1037: wdev_idx=0 [ 21.740619] WiFi@C08L2,ap_link_down() 7228: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(0) [ 21.749771] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(1) bss not ready (state:0, caller:APStopByBss+0xf8/0x4d0 [mt_wifi])!! [ 21.761315] WiFi@C08L2,ap_link_down() 7228: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(1) [ 21.770411] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(2) bss not ready (state:0, caller:APStopByBss+0xf8/0x4d0 [mt_wifi])!! [ 21.781939] WiFi@C08L2,ap_link_down() 7228: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(2) [ 21.791046] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(3) bss not ready (state:0, caller:APStopByBss+0xf8/0x4d0 [mt_wifi])!! [ 21.802571] WiFi@C08L2,ap_link_down() 7228: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(3) [ 21.811669] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(4) bss not ready (state:0, caller:APStopByBss+0xf8/0x4d0 [mt_wifi])!! [ 21.823188] WiFi@C08L2,ap_link_down() 7228: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(4) [ 21.832309] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(5) bss not ready (state:0, caller:APStopByBss+0xf8/0x4d0 [mt_wifi])!! [ 21.843841] WiFi@C08L2,ap_link_down() 7228: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(5) [ 21.852937] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(6) bss not ready (state:0, caller:APStopByBss+0xf8/0x4d0 [mt_wifi])!! [ 21.864458] WiFi@C08L2,ap_link_down() 7228: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(6) [ 21.873555] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(7) bss not ready (state:0, caller:APStopByBss+0xf8/0x4d0 [mt_wifi])!! [ 21.885072] WiFi@C08L2,ap_link_down() 7228: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(7) [ 21.894183] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(8) bss not ready (state:0, caller:APStopByBss+0xf8/0x4d0 [mt_wifi])!! [ 21.905713] WiFi@C08L2,ap_link_down() 7228: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(8) [ 21.914867] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(9) bss not ready (state:0, caller:APStopByBss+0xf8/0x4d0 [mt_wifi])!! [ 21.926401] WiFi@C08L2,ap_link_down() 7228: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(9) [ 21.935546] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(10) bss not ready (state:0, caller:APStopByBss+0xf8/0x4d0 [mt_wifi])!! [ 21.947167] WiFi@C08L2,ap_link_down() 7228: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(10) [ 21.956383] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(11) bss not ready (state:0, caller:APStopByBss+0xf8/0x4d0 [mt_wifi])!! [ 21.967998] WiFi@C08L2,ap_link_down() 7228: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(11) [ 21.977236] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(12) bss not ready (state:0, caller:APStopByBss+0xf8/0x4d0 [mt_wifi])!! [ 21.988855] WiFi@C08L2,ap_link_down() 7228: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(12) [ 21.998106] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(13) bss not ready (state:0, caller:APStopByBss+0xf8/0x4d0 [mt_wifi])!! [ 22.009728] WiFi@C08L2,ap_link_down() 7228: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(13) [ 22.018940] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(14) bss not ready (state:0, caller:APStopByBss+0xf8/0x4d0 [mt_wifi])!! [ 22.030552] WiFi@C08L2,ap_link_down() 7228: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(14) [ 22.039766] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(15) bss not ready (state:0, caller:APStopByBss+0xf8/0x4d0 [mt_wifi])!! [ 22.051388] WiFi@C08L2,ap_link_down() 7228: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(15) [ 22.060606] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(16) bss not ready (state:0, caller:APStopByBss+0xf8/0x4d0 [mt_wifi])!! [ 22.072222] WiFi@C08L2,ap_link_down() 7228: (caller:wdev_do_linkdown+0x20/0x38 [mt_wifi]), wdev(16) [ 22.081507] ch_switch_monitor_exit:: Exit [ 22.090524] current sync CR = 0x7 [ 22.093841] current sync CR = 0x7 [ 22.098139] current sync CR = 0x7 [ 22.102442] current sync CR = 0x7 [ 22.106743] current sync CR = 0x1 [ 22.238453] [Nop_List_Backup] NopList Channel count:0 <---- [ 22.259743] WiFi@C08L2,mbss_virtual_if_open() 133: ===> rax0 [ 22.265500] WiFi@C01L2,RTMP_COM_IoctlHandle() 1587: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 22.273839] msta_ifname not found [ 22.277205] single_ic_sku_path not found [ 22.281126] single_mkk_sku_path not found [ 22.285137] single_eg_sku_path not found [ 22.289104] bf_ic_sku_path not found [ 22.292683] bf_mkk_sku_path not found [ 22.296348] bf_eg_sku_path not found [ 22.337354] warp_dev1: probe of 15010000.wed2 failed with error -1 [ 22.343655] WiFi@C01L3,mt_wifi_open() 345: whnat_en=1 [ 22.476589] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(0) bss not ready (state:0, caller:TP_ROAMING_ReadParametersFromFile+0x154/0x2c0 [mt_wifi])!! [ 22.490054] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(1) bss not ready (state:0, caller:TP_ROAMING_ReadParametersFromFile+0x154/0x2c0 [mt_wifi])!! [ 22.503443] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(2) bss not ready (state:0, caller:TP_ROAMING_ReadParametersFromFile+0x154/0x2c0 [mt_wifi])!! [ 22.516807] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(3) bss not ready (state:0, caller:TP_ROAMING_ReadParametersFromFile+0x154/0x2c0 [mt_wifi])!! [ 22.530176] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(4) bss not ready (state:0, caller:TP_ROAMING_ReadParametersFromFile+0x154/0x2c0 [mt_wifi])!! [ 22.543541] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(5) bss not ready (state:0, caller:TP_ROAMING_ReadParametersFromFile+0x154/0x2c0 [mt_wifi])!! [ 22.556899] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(6) bss not ready (state:0, caller:TP_ROAMING_ReadParametersFromFile+0x154/0x2c0 [mt_wifi])!! [ 22.570264] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(7) bss not ready (state:0, caller:TP_ROAMING_ReadParametersFromFile+0x154/0x2c0 [mt_wifi])!! [ 22.585626] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS0 PhyMode=78 [ 22.592226] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS1 PhyMode=78 [ 22.598822] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS2 PhyMode=78 [ 22.605418] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS3 PhyMode=78 [ 22.612014] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS4 PhyMode=78 [ 22.618610] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS5 PhyMode=78 [ 22.625205] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS6 PhyMode=78 [ 22.631801] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS7 PhyMode=78 [ 22.638396] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS8 PhyMode=177 [ 22.645078] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS9 PhyMode=177 [ 22.651760] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS10 PhyMode=177 [ 22.658529] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS11 PhyMode=177 [ 22.665298] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS12 PhyMode=177 [ 22.672067] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS13 PhyMode=177 [ 22.678835] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS14 PhyMode=177 [ 22.685604] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS15 PhyMode=177 [ 22.692373] WiFi@C12L1,RTMPWirelessModeCfg() 619: Init: BSS16 PhyMode=177 [ 22.699458] WiFi@C23L3,auto_ch_select_set_cfg() 3551: BandIdx0, AutoChannelAtBootup=0, AutoChannelAlg = 0 [ 22.709001] WiFi@C23L3,auto_ch_select_set_cfg() 3551: BandIdx1, AutoChannelAtBootup=1, AutoChannelAlg = 3 [ 22.718940] WiFi@C00L2,RTMPChannelCfg() 383: Warning:ACS Enable and the 5G Channel of config parameter must set 0: [ 22.729262] WiFi@C00L2,RTMPChannelCfg() 383: Warning:ACS Enable and the 5G Channel of config parameter must set 0: [ 22.739583] WiFi@C00L2,RTMPChannelCfg() 383: Warning:ACS Enable and the 5G Channel of config parameter must set 0: [ 22.749904] WiFi@C00L2,RTMPChannelCfg() 383: Warning:ACS Enable and the 5G Channel of config parameter must set 0: [ 22.760230] WiFi@C00L2,RTMPChannelCfg() 383: Warning:ACS Enable and the 5G Channel of config parameter must set 0: [ 22.770556] WiFi@C00L2,RTMPChannelCfg() 383: Warning:ACS Enable and the 5G Channel of config parameter must set 0: [ 22.780877] WiFi@C00L2,RTMPChannelCfg() 383: Warning:ACS Enable and the 5G Channel of config parameter must set 0: [ 22.791198] WiFi@C00L2,RTMPChannelCfg() 383: Warning:ACS Enable and the 5G Channel of config parameter must set 0: [ 22.801518] WiFi@C00L2,RTMPChannelCfg() 383: Warning:ACS Enable and the 5G Channel of config parameter must set 0: [ 22.875139] IF(ra0) ==> radius_mac_type(seq-0)=0 [ 22.879742] IF(ra1) ==> radius_mac_type(seq-0)=0 [ 22.884343] IF(ra2) ==> radius_mac_type(seq-0)=0 [ 22.888944] IF(ra3) ==> radius_mac_type(seq-0)=0 [ 22.893544] IF(ra4) ==> radius_mac_type(seq-0)=0 [ 22.898145] IF(ra5) ==> radius_mac_type(seq-0)=0 [ 22.902745] IF(ra6) ==> radius_mac_type(seq-0)=0 [ 22.907345] IF(ra7) ==> radius_mac_type(seq-0)=0 [ 22.911945] IF(ra8) ==> radius_mac_type(seq-0)=0 [ 22.916546] IF(ra9) ==> radius_mac_type(seq-0)=0 [ 22.921145] IF(ra10) ==> radius_mac_type(seq-0)=0 [ 22.925833] IF(ra11) ==> radius_mac_type(seq-0)=0 [ 22.930520] IF(ra12) ==> radius_mac_type(seq-0)=0 [ 22.935207] IF(ra13) ==> radius_mac_type(seq-0)=0 [ 22.939895] IF(ra14) ==> radius_mac_type(seq-0)=0 [ 22.944582] IF(ra15) ==> radius_mac_type(seq-0)=0 [ 22.949269] IF(ra16) ==> radius_mac_type(seq-0)=0 [ 22.976082] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=0, Desired MFPC=1 [ 22.983458] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=1, Desired MFPC=1 [ 22.990834] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=2, Desired MFPC=1 [ 22.998210] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=3, Desired MFPC=1 [ 23.005585] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=4, Desired MFPC=1 [ 23.012960] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=5, Desired MFPC=1 [ 23.020337] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=6, Desired MFPC=1 [ 23.027713] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=7, Desired MFPC=1 [ 23.035088] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=8, Desired MFPC=1 [ 23.042463] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=9, Desired MFPC=1 [ 23.049839] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=10, Desired MFPC=1 [ 23.057300] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=11, Desired MFPC=1 [ 23.064762] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=12, Desired MFPC=1 [ 23.072224] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=13, Desired MFPC=1 [ 23.079686] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=14, Desired MFPC=1 [ 23.087148] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=15, Desired MFPC=1 [ 23.094609] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=16, Desired MFPC=1 [ 23.104079] WiFi@C12L1,RTMPSetProfileParameters() 9023: ra0, QoSMgmtCapa=0 [ 23.110936] WiFi@C12L1,RTMPSetProfileParameters() 9023: ra1, QoSMgmtCapa=0 [ 23.117792] WiFi@C12L1,RTMPSetProfileParameters() 9023: ra2, QoSMgmtCapa=0 [ 23.124647] WiFi@C12L1,RTMPSetProfileParameters() 9023: ra3, QoSMgmtCapa=0 [ 23.131502] WiFi@C12L1,RTMPSetProfileParameters() 9023: ra4, QoSMgmtCapa=0 [ 23.138357] WiFi@C12L1,RTMPSetProfileParameters() 9023: ra5, QoSMgmtCapa=0 [ 23.145213] WiFi@C12L1,RTMPSetProfileParameters() 9023: ra6, QoSMgmtCapa=0 [ 23.152069] WiFi@C12L1,RTMPSetProfileParameters() 9023: ra7, QoSMgmtCapa=0 [ 23.158924] WiFi@C12L1,RTMPSetProfileParameters() 9023: rax0, QoSMgmtCapa=0 [ 23.165866] WiFi@C12L1,RTMPSetProfileParameters() 9023: rax1, QoSMgmtCapa=0 [ 23.172809] WiFi@C12L1,RTMPSetProfileParameters() 9023: rax2, QoSMgmtCapa=0 [ 23.179751] WiFi@C12L1,RTMPSetProfileParameters() 9023: rax3, QoSMgmtCapa=0 [ 23.186692] WiFi@C12L1,RTMPSetProfileParameters() 9023: rax4, QoSMgmtCapa=0 [ 23.193634] WiFi@C12L1,RTMPSetProfileParameters() 9023: rax5, QoSMgmtCapa=0 [ 23.200576] WiFi@C12L1,RTMPSetProfileParameters() 9023: rax6, QoSMgmtCapa=0 [ 23.207518] WiFi@C12L1,RTMPSetProfileParameters() 9023: rax7, QoSMgmtCapa=0 [ 23.214467] WiFi@C12L1,RTMPSetProfileParameters() 9023: rax8, QoSMgmtCapa=0 [ 23.232179] WiFi@C12L1,rtmp_read_ap_client_from_file() 1649: APCLI[0] ApCliMuMimoDlEnable = 0 [ 23.240682] WiFi@C12L1,rtmp_read_ap_client_from_file() 1649: APCLI[1] ApCliMuMimoDlEnable = 0 [ 23.249378] WiFi@C12L1,rtmp_read_ap_client_from_file() 1668: APCLI[0] ApCliMuMimoUlEnable = 0 [ 23.257885] WiFi@C12L1,rtmp_read_ap_client_from_file() 1668: APCLI[1] ApCliMuMimoUlEnable = 0 [ 23.268560] WiFi@C03L1,AndesSendCmdMsg() 754: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD [ 23.279766] WiFi@C03L2,AndesSendCmdMsg() 765: Command type = ed, Extension command type = 48 [ 23.288203] WiFi@C03L1,AndesSendCmdMsg() 754: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD [ 23.299393] WiFi@C03L2,AndesSendCmdMsg() 765: Command type = ed, Extension command type = 48 [ 23.370453] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 23.376695] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(0)= Len=0 [ 23.383538] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 23.389776] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(1)= Len=0 [ 23.396619] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 23.402858] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(2)= Len=0 [ 23.409702] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 23.415941] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(3)= Len=0 [ 23.422783] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 23.429022] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(4)= Len=0 [ 23.435865] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 23.442103] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(5)= Len=0 [ 23.448946] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 23.455186] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(6)= Len=0 [ 23.462032] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 23.468273] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(7)= Len=0 [ 23.475256] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 23.481635] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(8)= Len=0 [ 23.488619] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 23.494999] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(9)= Len=0 [ 23.501983] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 23.508363] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(10)= Len=0 [ 23.515434] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 23.521816] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(11)= Len=0 [ 23.528886] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 23.535270] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(12)= Len=0 [ 23.542342] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 23.548724] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(13)= Len=0 [ 23.555795] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 23.562175] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(14)= Len=0 [ 23.569249] FT_rtmp_read_parameters_from_file: Invalid MdId=(null) [ 23.575632] FT_rtmp_read_parameters_from_file: Invalid FtRrbKey(15)= Len=0 [ 23.589939] I/F(ra0) FtPmkR1Local=0 [ 23.593413] I/F(ra1) FtPmkR1Local=0 [ 23.596883] I/F(ra2) FtPmkR1Local=0 [ 23.600357] I/F(ra3) FtPmkR1Local=0 [ 23.603830] I/F(ra4) FtPmkR1Local=0 [ 23.607304] I/F(ra5) FtPmkR1Local=0 [ 23.610777] I/F(ra6) FtPmkR1Local=0 [ 23.614251] I/F(ra7) FtPmkR1Local=0 [ 23.617724] I/F(ra8) FtPmkR1Local=0 [ 23.621194] I/F(ra9) FtPmkR1Local=0 [ 23.624668] I/F(ra10) FtPmkR1Local=0 [ 23.628228] I/F(ra11) FtPmkR1Local=0 [ 23.631788] I/F(ra12) FtPmkR1Local=0 [ 23.635348] I/F(ra13) FtPmkR1Local=0 [ 23.638907] I/F(ra14) FtPmkR1Local=0 [ 23.642467] I/F(ra15) FtPmkR1Local=0 [ 23.646026] I/F(ra16) FtPmkR1Local=0 [ 23.649809] I/F(ra0) pmkR0LifeTime=0 [ 23.653370] I/F(ra1) pmkR0LifeTime=0 [ 23.656927] I/F(ra2) pmkR0LifeTime=0 [ 23.660488] I/F(ra3) pmkR0LifeTime=0 [ 23.664048] I/F(ra4) pmkR0LifeTime=0 [ 23.667607] I/F(ra5) pmkR0LifeTime=0 [ 23.671167] I/F(ra6) pmkR0LifeTime=0 [ 23.674727] I/F(ra7) pmkR0LifeTime=0 [ 23.678287] I/F(ra8) pmkR0LifeTime=0 [ 23.681846] I/F(ra9) pmkR0LifeTime=0 [ 23.685407] I/F(ra10) pmkR0LifeTime=0 [ 23.689050] I/F(ra11) pmkR0LifeTime=0 [ 23.692696] I/F(ra12) pmkR0LifeTime=0 [ 23.696343] I/F(ra13) pmkR0LifeTime=0 [ 23.699989] I/F(ra14) pmkR0LifeTime=0 [ 23.703636] I/F(ra15) pmkR0LifeTime=0 [ 23.707282] I/F(ra16) pmkR0LifeTime=0 [ 23.711152] I/F(ra0) pmkR1LifeTime=0 [ 23.714712] I/F(ra1) pmkR1LifeTime=0 [ 23.718273] I/F(ra2) pmkR1LifeTime=0 [ 23.721833] I/F(ra3) pmkR1LifeTime=0 [ 23.725394] I/F(ra4) pmkR1LifeTime=0 [ 23.728951] I/F(ra5) pmkR1LifeTime=0 [ 23.732511] I/F(ra6) pmkR1LifeTime=0 [ 23.736071] I/F(ra7) pmkR1LifeTime=0 [ 23.739631] I/F(ra8) pmkR1LifeTime=0 [ 23.743191] I/F(ra9) pmkR1LifeTime=0 [ 23.746751] I/F(ra10) pmkR1LifeTime=0 [ 23.750397] I/F(ra11) pmkR1LifeTime=0 [ 23.754043] I/F(ra12) pmkR1LifeTime=0 [ 23.757689] I/F(ra13) pmkR1LifeTime=0 [ 23.761335] I/F(ra14) pmkR1LifeTime=0 [ 23.764979] I/F(ra15) pmkR1LifeTime=0 [ 23.768626] I/F(ra16) pmkR1LifeTime=0 [ 23.838826] sku:0xf, ADIE=MT7976 [ 23.843173] using E1 ROM patch [ 23.846213] using E1 RAM [ 23.848735] current sync CR = 0x1 [ 23.852158] Built date: 20230602115021a [ 23.856073] Platform: ALPS [ 23.858856] HW/SW version: 0x8a108a10 [ 23.862591] Patch version: 0xffffffff [ 23.866508] current sync CR = 0x1 [ 23.874635] Chip ID: 0x0f [ 23.877359] Eco version: 0x00 [ 23.880398] Region number: 0x0b [ 23.883613] Format version: 0x02 [ 23.886915] Format flag: 0x01 [ 23.889955] Ram version: ____000000 [ 23.893519] Built date: 20230602115044 [ 23.897344] Common crc: 0x9faa32f8 [ 23.900818] Release info: header tag = 0, total length = 80 [ 23.906463] tag 1, padding length = 1, tag length = 75 [ 23.911669] payload: t-neptune-main-2111-7986-imp-MT7986_E1_ASIC_ROM_RAM_REBB_IMP-20230602114602 [ 23.936625] Chip ID: 0x00 [ 23.939372] Eco version: 0x00 [ 23.942418] Region number: 0x03 [ 23.945633] Format version: 0x02 [ 23.948931] Format flag: 0x01 [ 23.951972] Ram version: DEV_000000 [ 23.955536] Built date: 20220906160431 [ 23.959361] Common crc: 0xa649edb8 [ 23.962837] Release info: header tag = 0, total length = 0 [ 24.062800] current sync CR = 0x7 [ 24.066181] efuse_probe: efuse = deaddead [ 24.070196] sku:0xf, ADIE=MT7976 [ 24.074538] Use default BIN from:/tmp/wireless/caldata.bin. [ 24.080958] sku:0xf, ADIE=MT7976 [ 24.086997] WiFi@C02L1,is_cal_free_ic() 1009: is_cal_free_ic(1009) offset:1000, 0,a [ 24.095417] sku:0xf, ADIE=MT7976 [ 24.113665] sku:0xf, ADIE=MT7976 [ 24.132089] WiFi@C02L1,is_cal_free_ic() 1028: iCal free [ 24.138080] sku:0xf, ADIE=MT7976 [ 28.117393] WiFi@C17L1,RTMPReadTxPwrPerRate() 450: (450): Don't Support this now! [ 28.124910] WiFi@C01L1,AntCfgInit() 3193: Not support for HIF_MT yet! [ 28.132317] WiFi@C01L1,RtmpOSFileOpen() 1012: Error 2 opening /tmp/wireless/mt7986_CE_sku_bf.dat [ 28.141081] --> Error opening file </tmp/wireless/mt7986_CE_sku_bf.dat> [ 28.147679] WiFi@C17L1,MtPwrLimitLoadParamHandle() 117: Read Power Table Error!! [ 28.162858] ch_switch_monitor_state_machine_init:: enter [ 28.168160] ch_switch_monitor_cfg_reset:: enter [ 28.172676] ch_switch_monitor_cfg_reset:: enter [ 28.177530] WiFi@C17L1,tx_pwr_comp_init() 641: NotSupportYet! [ 28.183379] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 28.188852] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 28.194321] WiFi@C14L1,IPMacTable_init() 348: IPMacTable already inited! [ 28.221216] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 28.226687] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 28.232110] WiFi@C00L1,set_ack_timeout_mode_byband() 13475: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 28.242003] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13563: DAT config band(0) cck_timeout Fail! [ 28.250678] WiFi@C00L1,set_ack_timeout_mode_byband() 13475: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 28.260566] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13574: DAT config band(0) ofdm_timeout Fail! [ 28.269328] WiFi@C00L1,set_ack_timeout_mode_byband() 13475: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 28.279217] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13585: DAT config band(0) ofdma_timeout Fail! [ 28.288075] WiFi@C00L1,set_ack_timeout_mode_byband() 13475: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 28.297972] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13563: DAT config band(1) cck_timeout Fail! [ 28.306654] WiFi@C00L1,set_ack_timeout_mode_byband() 13475: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 28.316542] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13574: DAT config band(1) ofdm_timeout Fail! [ 28.325305] WiFi@C00L1,set_ack_timeout_mode_byband() 13475: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 28.335199] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13585: DAT config band(1) ofdma_timeout Fail! [ 28.348401] :(op = 1) [ 28.355433] WiFi@C00L1,FastPathCheckMIC() 1010: (ret = 0)(op:1) [ 28.361340] WiFi@C00L2,red_tail_drop_init() 83: red_tail_drop_init: available token:8192, whnat_en:1 [ 28.370457] WiFi@C00L1,MtCmdCr4RedSet() 914: MtCmdCr4RedSet: (ret = 0) [ 28.376968] WiFi@C00L1,SendRedCmd() 1049: SendRedCmd:(ret = 1) [ 28.382850] WiFi@C01L2,RTMP_COM_IoctlHandle() 1564: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 28.390838] WiFi@C01L3,wifi_sys_open() 880: wdev idx = 8 [ 28.396414] WiFi@C18L3,BuildChannelList() 484: [ 28.400953] WiFi@C00L3,BuildChannelList() 514: BandIdx = 1, PhyMode = 177, ChListNum = 19: [ 28.409258] WiFi@C23L3,DfsBuildChannelList() 3748: Done [ 28.414495] WiFi@C23L3,RadarStateCheck() 244: Zero Wait State: 0 [ 28.420485] WiFi@C23L3,RadarStateCheck() 290: RD_NORMAL_MODE [ 28.427256] WiFi@C23L3,operate_loader_phy() 394: oper_cfg: prim_ch(0), ht_bw(1), extcha(1), vht_bw(1), cen_ch_2(0), PhyMode=177! [ 28.438789] phy_freq_adjust : no prim_ch value for adjust! [ 28.444258] WiFi@C23L1,operate_loader_phy() 398: phy_freq_adjust failed!WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xa4/0x158 [mt_wifi] [ 28.457662] /home/jenkins/workspace/PROJECT_EAP683LR_V1/build/../sdk/mtk/mt7986/drivers/mt_wifi/mt_wifi_ap/../mt_wifi/hw_ctrl/cmm_chip_mt.c-MtAsicSetMbssWdevIfAddrGen2 mbss_idx = 8, if_addr = 5c e9 31 7 cc 11 [ 28.476131] wdev_attr_update(): wdevId8 = 5c:e9:31:07:cc:11 [ 28.481702] WiFi@C12L1,wifi_sys_open() 931: wifi_sys_open():band1 group_idx[8]=4, bw_grp=16 omac=0 [ 28.490666] WiFi@C08L3,hw_ctrl_flow_v2_open() 13: wdev_idx=8 [ 28.497529] WiFi@C23L1,HcGetBandByChannel() 1230: No hdev parking on channel:0, just return a default band_idx 0! [ 28.507776] WiFi@C02L2,AsicRadioOnOffCtrl() 2340: DbdcIdx=0 RadioOn [ 28.514580] WiFi@C00L2,ApAutoChannelAtBootUp() 342: -----------------> [ 28.521185] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 28.526660] WiFi@C03L1,MtCmdSetMacTxRx() 10250: (ret = 0) [ 28.532057] WiFi@C23L3,AutoChSelBuildChannelListFor56G() 2799: ChListNum56G = 19 [ 28.539446] WiFi@C23L3,AutoChSelBuildChannelListFor56G() 2992: ACSChListNum = 4 [ 28.546953] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(8) bss not ready (state:0, caller:MTAPAutoSelectChannel+0x10c/0x448 [mt_wifi])!! [ 28.559220] WiFi@C00L1,mt7986_apply_dpd_flatness_data() 622: eeprom 0x19a bit 0 is 0, do runtime cal [ 28.568342] WiFi@C03L3,MtCmdChannelSwitch() 2542: ctrl_chl=36, ctrl_ch2=0, cent_ch=36 DBDCIdx=1, ChBand=1, BW=0, TXStream=4, RXStream=4, scan(1) [ 28.644538] WiFi@C03L3,MtCmdSetTxRxPath() 2803: ctrl_chl=36, ctrl_ch2=0, cent_ch=36, RxPath=f, BandIdx=1, ChBand=1, BW=0,TXStream=4, RXStream=15, scan(1) [ 28.869439] WiFi@C00L1,mt7986_apply_dpd_flatness_data() 622: eeprom 0x19a bit 0 is 0, do runtime cal [ 28.878555] WiFi@C03L3,MtCmdChannelSwitch() 2542: ctrl_chl=40, ctrl_ch2=0, cent_ch=40 DBDCIdx=1, ChBand=1, BW=0, TXStream=4, RXStream=4, scan(1) [ 28.954785] WiFi@C03L3,MtCmdSetTxRxPath() 2803: ctrl_chl=40, ctrl_ch2=0, cent_ch=40, RxPath=f, BandIdx=1, ChBand=1, BW=0,TXStream=4, RXStream=15, scan(1) [ 29.181441] WiFi@C00L1,mt7986_apply_dpd_flatness_data() 622: eeprom 0x19a bit 0 is 0, do runtime cal [ 29.190559] WiFi@C03L3,MtCmdChannelSwitch() 2542: ctrl_chl=44, ctrl_ch2=0, cent_ch=44 DBDCIdx=1, ChBand=1, BW=0, TXStream=4, RXStream=4, scan(1) [ 29.266802] WiFi@C03L3,MtCmdSetTxRxPath() 2803: ctrl_chl=44, ctrl_ch2=0, cent_ch=44, RxPath=f, BandIdx=1, ChBand=1, BW=0,TXStream=4, RXStream=15, scan(1) [ 29.425505] WiFi@C02L1,HcGetEdca() 1249: wdev=0, hobj is not ready! [ 29.493458] WiFi@C00L1,mt7986_apply_dpd_flatness_data() 622: eeprom 0x19a bit 0 is 0, do runtime cal [ 29.502580] WiFi@C03L3,MtCmdChannelSwitch() 2542: ctrl_chl=48, ctrl_ch2=0, cent_ch=48 DBDCIdx=1, ChBand=1, BW=0, TXStream=4, RXStream=4, scan(1) [ 29.578789] WiFi@C03L3,MtCmdSetTxRxPath() 2803: ctrl_chl=48, ctrl_ch2=0, cent_ch=48, RxPath=f, BandIdx=1, ChBand=1, BW=0,TXStream=4, RXStream=15, scan(1) [ 29.805680] WiFi@C08L1,UpdateBeaconHandler() 1896: wdev(8) bss not ready (state:0, caller:MTAPAutoSelectChannel+0x25c/0x448 [mt_wifi])!! [ 29.817925] WiFi@C23L3,SelectClearChannelBusyTime() 1947: ==================================================================== [ 29.829290] WiFi@C23L3,SelectClearChannelBusyTime() 1953: Channel 36 : Busy Time = 1118, Skip Channel = FALSE, BwCap = TRUE [ 29.840652] WiFi@C23L3,SelectClearChannelBusyTime() 1953: Channel 40 : Busy Time = 369, Skip Channel = FALSE, BwCap = TRUE [ 29.852166] WiFi@C23L3,SelectClearChannelBusyTime() 1953: Channel 44 : Busy Time = 1672, Skip Channel = FALSE, BwCap = TRUE [ 29.863531] WiFi@C23L3,SelectClearChannelBusyTime() 1953: Channel 48 : Busy Time = 1363, Skip Channel = FALSE, BwCap = TRUE [ 29.874892] WiFi@C23L3,SelectClearChannelBusyTime() 1956: ==================================================================== [ 29.886263] WiFi@C23L3,SelectClearChannelBusyTime() 2192: Rule 3 Channel Busy time value : Select Primary Channel 40 [ 29.896760] WiFi@C23L3,SelectClearChannelBusyTime() 2194: Rule 3 Channel Busy time value : Min Channel Busy = 1672 [ 29.907084] WiFi@C23L3,SelectClearChannelBusyTime() 2199: Rule 3 Channel Busy time value : BW = 80 [ 29.916022] WiFi@C23L3,SelectClearChannelBusyTime() 2233: [SelectClearChannelBusyTime] - band1 END [ 29.924975] WiFi@C23L3,RadarStateCheck() 244: Zero Wait State: 0 [ 29.930966] WiFi@C23L3,RadarStateCheck() 290: RD_NORMAL_MODE [ 29.937746] WiFi@C23L3,operate_loader_phy() 394: oper_cfg: prim_ch(40), ht_bw(1), extcha(1), vht_bw(1), cen_ch_2(0), PhyMode=177! [ 29.949375] WiFi@C23L3,operate_loader_phy() 408: oper_dev after adjust: bw(2), prim_ch(40), cen_ch_1(42), cen_ch_2(0),ext_cha(3)! [ 29.961022] WiFi@C23L3,operate_loader_phy() 428: oper_radio after decision: bw(2), prim_ch(40), cen_ch_1(42), cen_ch_2(0)! [ 29.972066] WiFi@C00L1,mt7986_apply_dpd_flatness_data() 622: eeprom 0x19a bit 0 is 0, do runtime cal [ 29.981184] WiFi@C03L3,MtCmdChannelSwitch() 2542: ctrl_chl=40, ctrl_ch2=0, cent_ch=42 DBDCIdx=1, ChBand=1, BW=2, TXStream=4, RXStream=4, scan(0) [ 30.342291] WiFi@C03L3,MtCmdSetTxRxPath() 2803: ctrl_chl=40, ctrl_ch2=0, cent_ch=42, RxPath=f, BandIdx=1, ChBand=1, BW=2,TXStream=4, RXStream=15, scan(0) [ 30.361166] WiFi@C12L1,EDCCAInit() 21458: EDCCA compensation: uni_compensation=0, bw_compensation=0, final compensation=0 [ 30.372150] WiFi@C23L3,DfsBuildChannelList() 3748: Done [ 30.377371] WiFi@C23L3,zero_wait_dfs_switch_ch() 928: outband ch 0, ch_stat 0 [ 30.384487] WiFi@C23L3,zero_wait_dfs_switch_ch() 935: bDedicatedZeroWaitDefault == 0 [ 30.392463] WiFi@C08L2,APStartUpForMbss() 1001: ===>(caller:ap_inf_open+0x1b4/0x5d8 [mt_wifi]), mbss_idx:8, CfgMode:0 [ 30.403053] WiFi@C15L2,APPMFInit() 142: [PMF] apidx=8, MFPC=1, MFPR=0, SHA256=0 [ 30.410352] WiFi@C18L3,BuildChannelList() 484: [ 30.415107] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 30.422663] WiFi@C08L2,ap_link_up() 7210: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(8) [ 30.431265] WiFi@C01L3,wifi_sys_linkup() 1291: wdev idx = 8 [ 30.482628] WiFi@C00L3,wtc_acquire_groupkey_wcid() 84: Found a non-occupied wtbl_idx:535 for WDEV_TYPE:1 [ 30.482628] LinkToOmacIdx = 0, LinkToWdevType = 1 [ 30.496978] WiFi@C08L3,hw_ctrl_flow_v2_link_up() 72: wdev_idx=8 [ 30.511068] WiFi@C08L3,UpdateBeaconHandler() 1916: BCN_UPDATE_INIT, OmacIdx = 0 (rax0) [ 30.519055] WiFi@C08L3,UpdateBeaconHandler() 1929: Band1 BcnInitedRnd = 20 [ 30.538148] PrintSrCmd: [ 30.538148] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 30.538148] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 30.552121] PrintSrCmd: [ 30.552121] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 30.552121] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 30.566090] PrintSrCmd: [ 30.566090] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 30.566090] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 30.580056] PrintSrCmd: [ 30.580056] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 30.580056] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 30.594112] PrintSrCmd: [ 30.594112] u1CmdSubId = 31, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 30.594112] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 30.608170] PrintSrCmd: [ 30.608170] u1CmdSubId = 33, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 30.608170] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 30.622245] WiFi@C12L1,EDCCAInit() 21458: EDCCA compensation: uni_compensation=0, bw_compensation=0, final compensation=0 [ 30.633181] WiFi@C03L3,MtCmdTxPwrShowInfo() 13750: ucTxPowerInfoCatg: 2, BandIdx: 1 [ 30.640908] WiFi@C03L3,MtCmdTxPwrShowInfo() 13779: (ret = 0) [ 30.641001] [mtf_txpower_all_rate_info] band_idx:1 pwr:30 ChBand:5G ePAGain:0 [ 30.706983] wnm enable: 0 [ 30.716261] dualband enable: 0 <error>radio_reg[ 30.841109] [ 30.841109] manage vlan set ssid vlan: idx (0), intfName (rax0), vlan (0) ion_getChanCommonFlag():1056 @ invalid chanIndex:0, current channelNum = 19 [ 30.862703] wnm enable: 0 [ 30.871892] dualband enable: 0 look up /tmp/wireless/caldata.bin succ result=1 [ 30.913655] tp mesh events being sent to PID:941 [ 31.025216] BcnCheck start after 4500 ms (ra0) [ 31.122744] [Debug gpo_proc_write:234] Write ble_reset. [ 31.329407] [Debug gpo_proc_write:234] Write ble_reset. [BLE_DEBUG]<debug>[bleCcDnld_bleFirwareChecking:384] ble controller software is:1.0.2 [BLE_DEBUG]<debug>[bleCcDnld_bleFirwareChecking:385] hostFirwareVersion software is:1.0.2 [BLE_DEBUG]<debug>[bleCcDnld_bleFirwareChecking:394] ble has the same portion 0 type version as host, keep it [ 31.939547] [Debug gpo_proc_write:234] Write ble_reset. [ 32.146335] [Debug gpo_proc_write:234] Write ble_reset. [BLE_DEBUG]<debug>[bleCcDnld_bleFirwareChecking:384] ble controller software is:1.0.0 [BLE_DEBUG]<debug>[bleCcDnld_bleFirwareChecking:385] hostFirwareVersion software is:1.0.0 [BLE_DEBUG]<debug>[bleCcDnld_bleFirwareChecking:394] ble has the same portion 1 type version as host, keep it [ 32.756355] [Debug gpo_proc_write:234] Write ble_reset. [ 32.963128] [Debug gpo_proc_write:234] Write ble_reset. [Debug gpoListen[ 33.372601] [Debug led_proc_write:657] Write led_sys. EventHandler:149[ 33.377997] [Debug led_common_write_proc:496] Execute LED action: ] Accept a new c[ 33.378000] { 3 0 500 500 4 } lient. [Debug gpoClientEventHandler:111] GPIOD received rule: LED_SYS_INIT_OK. [ 33.629207] BcnCheck start after 2000 ms (ra0) iptables: Bad rule (does a matching rule exist in that chain?). [Debug gpoListen[ 35.915724] [Debug led_proc_write:657] Write led_sys. EventHandler:149[ 35.921158] [Debug led_common_write_proc:496] Execute LED action: ] Accept a new c[ 35.921160] { 7 0 0 0 0 } lient. [Debug gpoClientEventHandler:111] GPIOD received rule: LED_ISOLATED_FINISH. now ok to start tddp--------------------- uclite init ok, now startup eap-cs --------------------- [TDDP_DEBUG]<debug>[main:1338] tddp init--- <httpd>[debug]http_inetd_addListenSocket(): 719 -> listen add port(80), ssl(0) <httpd>[debug]http_inetd_addListenSocket(): 719 -> listen add port(443), ssl(1) <httpd>[debug]http_inetd_addListenSocket(): 719 -> listen add port(22080), ssl(0) <httpd>[debug]http_inetd_addListenSocket(): 719 -> listen add port(22443), ssl(1) <httpd>[debug]http_inetd_addListenSocket(): 719 -> listen add port(33443), ssl(1) <httpd>[debug]http_inetd_addListenSocket(): 719 -> listen add port(44443), ssl(1) <httpd>[debug]http_inetd_addListenSocket(): 719 -> listen add port(33080), ssl(0) route: SIOCDELRT: No such process [UNIX_SOCK][unix_sock_connSrv:301]connect to file(/var/run/srv/22) failed after retry(0), errno(2):No such file or directory [ 45.198327] tp dfs events being sent to PID:965 drop caches--------------------- Into util_dbg_setMod, pModName(all), enable(1)

# dmesg [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 6.12.68 (stijn@taz) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 14.3.0 r24330+8341-c2a30b6e01) 14.3.0, GNU ld (GNU Binutils) 2.44) #0 SMP Sat Feb 7 08:14:50 2026 [ 0.000000] Machine model: TP-Link EAP683-LR [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options '') [ 0.000000] printk: legacy bootconsole [uart8250] enabled [ 0.000000] OF: reserved mem: 0x0000000042ff0000..0x0000000042ffffff (64 KiB) map non-reusable ramoops@42ff0000 [ 0.000000] OF: reserved mem: 0x0000000043000000..0x000000004303ffff (256 KiB) nomap non-reusable secmon@43000000 [ 0.000000] OF: reserved mem: 0x000000004fc00000..0x000000004fcfffff (1024 KiB) nomap non-reusable wmcpu-reserved@4fc00000 [ 0.000000] OF: reserved mem: 0x000000004fd00000..0x000000004fd3ffff (256 KiB) nomap non-reusable wo-emi@4fd00000 [ 0.000000] OF: reserved mem: 0x000000004fd40000..0x000000004fd7ffff (256 KiB) nomap non-reusable wo-emi@4fd40000 [ 0.000000] OF: reserved mem: 0x000000004fd80000..0x000000004ffbffff (2304 KiB) nomap non-reusable wo-data@4fd80000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff] [ 0.000000] node 0: [mem 0x0000000043000000-0x000000004303ffff] [ 0.000000] node 0: [mem 0x0000000043040000-0x000000004fbfffff] [ 0.000000] node 0: [mem 0x000000004fc00000-0x000000004ffbffff] [ 0.000000] node 0: [mem 0x000000004ffc0000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 20 pages/cpu s42776 r8192 d30952 u81920 [ 0.000000] pcpu-alloc: s42776 r8192 d30952 u81920 alloc=20*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttyS0,115200n1 ubi.mtd=rootfs root=/dev/ubiblock0_0 rootfstype=squashfs rootwait loglevel=8 earlycon=uart8250,mmio32,0x11002000 ubi.mtd=ubi root=/dev/ubiblock0_1 [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 262144 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] stackdepot: allocating hash table via alloc_large_system_hash [ 0.000000] stackdepot hash table entries: 65536 (order: 8, 1048576 bytes, linear) [ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 1MB [ 0.000000] software IO TLB: area num 4. [ 0.000000] software IO TLB: mapped [mem 0x000000007fa06000-0x000000007fb06000] (1MB) [ 0.000000] ********************************************************** [ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.000000] ** ** [ 0.000000] ** This system shows unhashed kernel memory addresses ** [ 0.000000] ** via the console, logs, and other interfaces. This ** [ 0.000000] ** might reduce the security of your system. ** [ 0.000000] ** ** [ 0.000000] ** If you see this message and you are not debugging ** [ 0.000000] ** the kernel, report this immediately to your system ** [ 0.000000] ** administrator! ** [ 0.000000] ** ** [ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.000000] ********************************************************** [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 640 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv3: GICv3 features: 16 PPIs [ 0.000000] GICv3: GICD_CTRL.DS=0, SCR_EL3.FIQ=0 [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns [ 0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns [ 0.008138] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000) [ 0.018543] pid_max: default: 32768 minimum: 301 [ 0.024889] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.032327] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.042282] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.049623] rcu: Hierarchical SRCU implementation. [ 0.054441] rcu: Max phase no-delay instances is 1000. [ 0.059927] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.068412] smp: Bringing up secondary CPUs ... [ 0.073489] Detected VIPT I-cache on CPU1 [ 0.073542] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000 [ 0.073574] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.074090] Detected VIPT I-cache on CPU2 [ 0.074123] GICv3: CPU2: found redistributor 2 region 0:0x000000000c0c0000 [ 0.074139] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.074568] Detected VIPT I-cache on CPU3 [ 0.074590] GICv3: CPU3: found redistributor 3 region 0:0x000000000c0e0000 [ 0.074603] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.074647] smp: Brought up 1 node, 4 CPUs [ 0.131219] SMP: Total of 4 processors activated. [ 0.135939] CPU: All CPU(s) started at EL2 [ 0.140047] CPU features: detected: 32-bit EL0 Support [ 0.145207] CPU features: detected: CRC32 instructions [ 0.150388] alternatives: applying system-wide alternatives [ 0.156105] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching [ 0.164778] Memory: 1004496K/1048576K available (9536K kernel code, 988K rwdata, 2780K rodata, 512K init, 368K bss, 41028K reserved, 0K cma-reserved) [ 0.185590] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.195496] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.202537] 29184 pages in range for non-PLT usage [ 0.202541] 520704 pages in range for PLT usage [ 0.207794] pinctrl core: initialized pinctrl subsystem [ 0.219283] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.225879] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations [ 0.233011] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.240818] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.249695] thermal_sys: Registered thermal governor 'fair_share' [ 0.249699] thermal_sys: Registered thermal governor 'bang_bang' [ 0.255815] thermal_sys: Registered thermal governor 'step_wise' [ 0.261850] thermal_sys: Registered thermal governor 'user_space' [ 0.268041] ASID allocator initialised with 65536 entries [ 0.281053] pstore: Using crash dump compression: deflate [ 0.286489] pstore: Registered ramoops as persistent store backend [ 0.292694] ramoops: using 0x10000@0x42ff0000, ecc: 0 [ 0.299043] /soc/interrupt-controller@c000000: Fixed dependency cycle(s) with /soc/interrupt-controller@c000000 [ 0.317101] /soc/pcie@11280000: Fixed dependency cycle(s) with /soc/pcie@11280000/interrupt-controller [ 0.333186] cryptd: max_cpu_qlen set to 1000 [ 0.339627] SCSI subsystem initialized [ 0.343678] libata version 3.00 loaded. [ 0.350807] clocksource: Switched to clocksource arch_sys_counter [ 0.359824] NET: Registered PF_INET protocol family [ 0.365007] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.373588] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.382007] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.389897] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.397744] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 0.405184] TCP: Hash tables configured (established 8192 bind 8192) [ 0.412026] MPTCP token hash table entries: 1024 (order: 3, 24576 bytes, linear) [ 0.419566] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.426242] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.433924] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.439676] PCI: CLS 0 bytes, default 64 [ 0.445520] workingset: timestamp_bits=46 max_order=18 bucket_order=0 [ 0.457088] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.462989] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.512308] gpio-export gpio-export: 2 gpio(s) exported [ 0.518502] mtk-pcie-gen3 11280000.pcie: host bridge /soc/pcie@11280000 ranges: [ 0.525893] mtk-pcie-gen3 11280000.pcie: Parsing ranges property... [ 0.532201] mtk-pcie-gen3 11280000.pcie: MEM 0x0020000000..0x002fffffff -> 0x0020000000 [ 0.540996] /soc/pcie@11280000: Failed to get clk index: 0 ret: -517 [ 0.547391] mtk-pcie-gen3 11280000.pcie: failed to get clocks [ 0.559469] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 0.568188] printk: legacy console [ttyS0] disabled [ 0.593735] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 116, base_baud = 2500000) is a ST16650V2 [ 0.603048] printk: legacy console [ttyS0] enabled [ 0.612623] printk: legacy bootconsole [uart8250] disabled [ 0.645419] 11004000.serial: ttyS1 at MMIO 0x11004000 (irq = 117, base_baud = 1625000) is a ST16650V2 [ 0.655813] mtk_rng 1020f000.rng: registered RNG driver [ 0.656050] random: crng init done [ 0.670078] loop: module loaded [ 0.676157] spi-nand spi0.0: ESMT SPI NAND was found. [ 0.681259] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64 [ 0.689896] Signature found at block 1023 [0x07fe0000] [ 0.695025] NMBM management region starts at block 960 [0x07800000] [ 0.702346] First info table with writecount 1 found in block 960 [ 0.711400] Second info table with writecount 1 found in block 963 [ 0.717578] NMBM has been successfully attached [ 0.722497] 13 fixed-partitions partitions found on MTD device spi0.0 [ 0.729300] Creating 13 MTD partitions on "spi0.0": [ 0.734201] 0x000000000000-0x000000100000 : "BL2" [ 0.740282] 0x000000100000-0x000000200000 : "boot-config" [ 0.746943] 0x000000200000-0x000000300000 : "boot-config1" [ 0.753658] 0x000000300000-0x000000400000 : "u-boot-env" [ 0.760129] 0x000000400000-0x000000600000 : "FIP0" [ 0.766731] 0x000000600000-0x000000800000 : "FIP1" [ 0.773334] 0x000000800000-0x000000900000 : "oops" [ 0.779325] 0x000000900000-0x000002f80000 : "ubi" [ 0.805839] 0x000002f80000-0x000005600000 : "ubi1" [ 0.832158] 0x000005600000-0x000005e00000 : "factory" [ 0.842267] 0x000005e00000-0x000006a00000 : "runtime_data" [ 0.855152] 0x000006a00000-0x000007200000 : "backup_data" [ 0.865556] 0x000007200000-0x000007800000 : "runtime_backup" [ 1.012156] mtk_soc_eth 15100000.ethernet: generated random MAC address 20:08:02:00:00:00 [ 1.063882] Maxlinear Ethernet GPY211C mdio-bus:05: Firmware Version: 8.111 (0x886F) [ 1.076416] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc081880000, irq 121 [ 1.086544] i2c_dev: i2c /dev entries driver [ 1.093118] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0) [ 1.102136] NET: Registered PF_INET6 protocol family [ 1.108671] Segment Routing with IPv6 [ 1.112451] In-situ OAM (IOAM) with IPv6 [ 1.116441] NET: Registered PF_PACKET protocol family [ 1.121708] 8021q: 802.1Q VLAN Support v1.8 [ 1.162047] mt7986a-pinctrl 1001f000.pinctrl: pin GPIO_5 already requested by pinctrl_moore:522; cannot claim for 11280000.pcie [ 1.173872] mt7986a-pinctrl 1001f000.pinctrl: error -EINVAL: pin-10 (11280000.pcie) [ 1.181575] mt7986a-pinctrl 1001f000.pinctrl: error -EINVAL: could not request pin 10 (GPIO_5) from group pcie_wake on device pinctrl_moore [ 1.194151] mtk-pcie-gen3 11280000.pcie: Error applying setting, reverse things back [ 1.203478] UBI error: cannot open mtd rootfs, error -2 [ 1.208760] ubi0: default fastmap pool size: 15 [ 1.213292] ubi0: default fastmap WL pool size: 7 [ 1.217978] ubi0: attaching mtd7 [ 1.359238] ubi0: scanning is finished [ 1.421734] ubi0: attached mtd7 (name "ubi", size 38 MiB) [ 1.427137] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 1.434011] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 1.440778] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 1.447722] ubi0: good PEBs: 308, bad PEBs: 0, corrupted PEBs: 0 [ 1.453713] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 [ 1.460915] ubi0: max/mean erase counter: 38/29, WL threshold: 4096, image sequence number: 1951148539 [ 1.470196] ubi0: available PEBs: 0, total reserved PEBs: 308, PEBs reserved for bad PEB handling: 19 [ 1.479400] ubi0: background thread "ubi_bgt0d" started, PID 592 [ 1.480598] block ubiblock0_1: created from ubi0:1(rootfs) [ 1.490877] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem [ 1.497971] clk: Disabling unused clocks [ 1.502146] PM: genpd: Disabling unused power domains [ 1.520845] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 1.528210] Freeing unused kernel memory: 512K [ 1.532719] Run /sbin/init as init process [ 1.536801] with arguments: [ 1.539752] /sbin/init [ 1.542458] with environment: [ 1.545583] HOME=/ [ 1.547929] TERM=linux [ 1.715397] init: Console is alive [ 1.719025] init: - watchdog - [ 1.998536] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 2.016375] gpio_button_hotplug: loading out-of-tree module taints kernel. [ 2.027224] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 2.035536] init: - preinit - [ 2.477523] mtk_soc_eth 15100000.ethernet eth0: PHY [mdio-bus:05] driver [Maxlinear Ethernet GPY211C] (irq=POLL) [ 2.491937] mtk_soc_eth 15100000.ethernet eth0: configuring for phy/2500base-x link mode [ 2.545796] ubi1: default fastmap pool size: 8 [ 2.550243] ubi1: default fastmap WL pool size: 4 [ 2.554976] ubi1: attaching mtd9 [ 2.558192] ubi1: MTD device 9 is write-protected, attach in read-only mode [ 2.593545] ubi1: scanning is finished [ 2.602599] ubi1 warning: ubi_eba_init: cannot reserve enough PEBs for bad PEB handling, reserved 17, need 19 [ 2.721636] ubi1: attached mtd9 (name "factory", size 8 MiB) [ 2.727298] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 2.734183] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 2.740984] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 2.747927] ubi1: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0 [ 2.753837] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 2.761042] ubi1: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 1499378563 [ 2.770150] ubi1: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 17 [ 2.779270] ubi1: background thread "ubi_bgt1d" started, PID 693 [ 2.788062] UBIFS (ubi1:0): read-only UBI device [ 2.793277] UBIFS (ubi1:0): Mounting in unauthenticated mode [ 2.847705] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "ubi_factory_data", R/O mode [ 2.856852] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 2.866746] UBIFS (ubi1:0): FS size: 3936256 bytes (3 MiB, 31 LEBs), max 60 LEBs, journal size 1269760 bytes (1 MiB, 10 LEBs) [ 2.878028] UBIFS (ubi1:0): reserved for root: 0 bytes (0 KiB) [ 2.883845] UBIFS (ubi1:0): media format: w4/r0 (latest is w5/r0), UUID A482D59E-0EB7-41C5-AAE4-41C5DD83D57E, small LPT model [ 6.671835] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control off [ 7.146048] UBIFS (ubi0:2): Mounting in unauthenticated mode [ 7.151981] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 736 [ 7.185827] UBIFS (ubi0:2): recovery needed [ 7.290825] UBIFS (ubi0:2): recovery completed [ 7.295373] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data" [ 7.303189] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 7.313095] UBIFS (ubi0:2): FS size: 13967360 bytes (13 MiB, 110 LEBs), max 120 LEBs, journal size 1015809 bytes (0 MiB, 6 LEBs) [ 7.324635] UBIFS (ubi0:2): reserved for root: 659712 bytes (644 KiB) [ 7.331061] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID E1B077B9-87EE-45BB-87C3-336997F1A4A9, small LPT model [ 7.346939] mount_root: switching to ubifs overlay [ 7.356585] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off. [ 7.373241] urandom-seed: Seeding with /etc/urandom.seed [ 7.424747] procd: - early - [ 7.427740] procd: - watchdog - [ 7.977036] procd: - watchdog - [ 7.982028] procd: - ubus - [ 8.139922] procd: - init - [ 8.471297] kmodloader: loading kernel modules from /etc/modules.d/* [ 8.498627] tun: Universal TUN/TAP device driver, 1.6 [ 8.505518] GACT probability on [ 8.509773] Mirror/redirect action on [ 8.520411] u32 classifier [ 8.523148] input device check on [ 8.526794] Actions configured [ 8.538363] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433(alg:7fcdfc00)/0/0/0 [ 8.555601] Loading modules backported from Linux version v6.18.7-0-g5dfbc5357 [ 8.562892] Backport generated by backports.git c8a37ce [ 8.641659] urngd: v1.0.2 started. [ 8.984210] mt798x-wmac 18000000.wifi: HW/SW Version: 0x8a108a10, Build Time: 20240823160656a [ 9.130157] mt798x-wmac 18000000.wifi: WM Firmware Version: ____000000, Build Time: 20240823160721 [ 9.222904] mt798x-wmac 18000000.wifi: WA Firmware Version: DEV_000000, Build Time: 20240823160840 [ 9.370643] mt798x-wmac 18000000.wifi: eeprom load fail, use default bin [ 9.430851] mt798x-wmac 18000000.wifi: registering led 'mt76-phy0' [ 9.492977] mt798x-wmac 18000000.wifi: registering led 'mt76-phy1' [ 9.587974] PPP generic driver version 2.4.2 [ 9.594506] NET: Registered PF_PPPOX protocol family [ 9.604463] kmodloader: done loading kernel modules from /etc/modules.d/* [ 12.716520] mtk_soc_eth 15100000.ethernet eth0: Link is Down [ 13.157474] mtk_soc_eth 15100000.ethernet eth0: PHY [mdio-bus:05] driver [Maxlinear Ethernet GPY211C] (irq=POLL) [ 13.173220] mtk_soc_eth 15100000.ethernet eth0: configuring for phy/2500base-x link mode

Space for additional notes, links to forum threads or other resources.

TP-Link website GPL source tarballs:

ShoutWiki pages:

GitHub PR: https://github.com/openwrt/openwrt/pull/20319

How to add tags

mediatek, filogic, MT7986, 4core, 128NAND, 1024RAM, 1port, 2.5GigabitEthernet, u-boot, 2WNIC, 4x4, 802.11bgn, 802.11anac, 802.11ax, wifi6, InternalAntenna, 0usb, 1button, hwVLAN, ARMv8, cortexa53, crypto, serial, 12v powered, PoE, ceiling

mediatek filogic mt7986 4core 128nand 1024ram 1port 2.5gigabitethernet u-boot 2wnic 4x4 802.11bgn 802.11anac 802.11ax wifi6 internalantenna 0usb 1button hwvlan armv8 cortexa53 crypto serial 12v powered PoE ceiling

TP-Link EAP683-LR

Supported Versions

Hardware Highlights

Installation

Additional: Installing OpenThread-BR from cc2652_backdoor

Flash Layout

OEM easy installation

OEM installation using the TFTP method

Specific values needed for tftp

Upgrading OpenWrt

LuCI Web Upgrade Process

Terminal Upgrade Process

sysupgrade

mtd

Debricking

Failsafe mode

Basic configuration

Specific Configuration

Network interfaces

Switch Ports (for VLANs)

Buttons

Hardware

Info

Photos

Opening the case

Serial

JTAG

Bootloader mods

Hardware mods

Bootlogs

OEM bootlog

OpenWrt bootlog

Notes

Tags