Iomega NAS 100d

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

The Iomega NAS 100d is the only device in this roundup to offer wireless networking connectivity. But this functionality has to be weighed against outdated wireless security and a complete lack of data security due to the number of accumulated security flaws in this device. The OpenWrt images are recommended for use of this device.

The Iomega NAS 100d offers connectivity via Ethernet, 802.11g wireless networking and expandable via two USB 2.0 ports.

Supported Versions

Hardware Highlights

Installation

→ Install OpenWrt (generic explanation)

Please add the installation procedure here.

Flash Layout

Find out flash layout, then add the flash layout table here (copy, paste, modify the example).

Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.

OEM installation using the TFTP method

→ generic.flashing.tftp

Specific values needed for tftp

Enter values for “FILL-IN” below

Bootloader tftp server IPv4 address	FILL-IN
Bootloader MAC address (special)	FILL-IN
Firmware tftp image	Latest OpenWrt release (`NOTE:` Name must contain “tftp”)
TFTP transfer window	FILL-IN seconds
TFTP window start	approximately FILL-IN seconds after power on
TFTP client required IP address	FILL-IN

Debricking

→ generic.debrick

Failsafe mode

→ failsafe_and_factory_reset

Basic configuration

→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Specific Configuration

Please fill in real values for this device, then remove the EXAMPLEs

Network interfaces

The default network configuration is:

Interface Name	Description	Default configuration
br-lan	EXAMPLE LAN & WiFi	EXAMPLE 192.168.1.1/24
vlan0 (eth0.0)	EXAMPLE LAN ports (1 to 4)	EXAMPLE None
vlan1 (eth0.1)	EXAMPLE WAN port	EXAMPLE DHCP
wl0	EXAMPLE WiFi	EXAMPLE Disabled

Switch Ports (for VLANs)

No VLAN for this device.

Buttons

→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

Please fill in real values for this device, then remove the EXAMPLEs

The Iomega NAS 100d has the following buttons:

BUTTON	Event
EXAMPLE Reset	reset
EXAMPLE Secure Easy Setup	ses
EXAMPLE No buttons at all.	-

Hardware

Info

Photos

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Backside label:
Insert photo of backside label

Opening the case

→ Warranty

Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, ...

To remove the cover and open the device, do a/b/c

Main PCB:
Insert photo of PCB

Serial

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

Serial connection parameters for Iomega NAS 100d	115200, 8N1, 3.3V (untested)

JTAG

→ port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Bootloader mods

→ bootloader

Hardware mods

None so far.

Bootlogs

OEM bootlog

COPY HERE THE BOOTLOG WITH THE ORIGINAL FIRMWARE

OpenWrt bootlog

COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING

Notes

Space for additional notes, links to forum threads or other resources.

Table of Contents